Contents
2016
Volume: 4 Issue 6
20 Article(s)
Export citation format
Fiber Optics and Optical Communications
Investigation on performance of special-shaped 8-quadrature amplitude modulation constellations applied in visible light communication
Jiaqi Zhao, Chaoyi Qin, Mengjie Zhang, and Nan Chi
Light-emitting diode (LED)-based visible light communication (VLC) has become a potential candidate for nextgeneration ultra-high-speed indoor wireless communication. In this paper, four special-shaped 8-quadrature amplitude modulation (QAM) constellations are investigated in a single-carrier VLC system. It is numericaLight-emitting diode (LED)-based visible light communication (VLC) has become a potential candidate for nextgeneration ultra-high-speed indoor wireless communication. In this paper, four special-shaped 8-quadrature amplitude modulation (QAM) constellations are investigated in a single-carrier VLC system. It is numerically verified and experimentally demonstrated that circular (7,1) shows obvious superiority in the performance of the dynamic range of signal voltage peak-to-peak (vpp) value and bit error rate (BER). Next best is rectangular, followed by triangular; circular (4,4) has the worst performance. A data rate of 1.515 Gbit/s is successfully achieved by circular (7,1) employing a red chip LED over 0.5 m indoor free space transmission below a BER threshold of 3.8 × 10?3. Compared with circular (4,4), the traditional 8-QAM constellation, circular (7,1) provides a wider dynamic range of signal vpp, a higher data rate, and a longer transmission distance. To the best of our knowledge, this is the first investigation into the performance differences of special-shaped 8-QAM constellations in a highspeed, single-carrier VLC system, and the results comprehensively demonstrate that circular (7,1) is the optimal option..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 249 (2016)
Imaging
Scalar-matrix-structured ghost imaging
Chao Yang, Chenglong Wang, Jian Guan, Chi Zhang... and Fengli Gao|Show fewer author(s)
The features of the characteristic matrix used in linear intensity correlation reconstruction methods are directly related to the quality of ghost imaging. In order to suppress the noise caused by the off-diagonal elements in the characteristic matrix, we propose a reconstruction method for ghost imaging called scalar-The features of the characteristic matrix used in linear intensity correlation reconstruction methods are directly related to the quality of ghost imaging. In order to suppress the noise caused by the off-diagonal elements in the characteristic matrix, we propose a reconstruction method for ghost imaging called scalar-matrix-structured ghost imaging (SMGI). The characteristic matrix is made to approximate a scalar matrix by modifying the measurement matrix. Experimental results show that SMGI improves the peak signal-to-noise ratio of the object reconstruction significantly compared with differential ghost imaging, even in the case of a nonzero two-arm longitudinal difference, which is a promising result for practical applications.of China (2013AA122901); National Natural Science Foundation of China (NSFC) (61571427); Youth Innovation Promotion Association of the Chinese Academy of Sciences (2013162)..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 281 (2016)
Detection and upconversion of three-dimensional MMW/THz images to the visible
Avihai Aharon (Akram), Daniel Rozban, Avi Klein, Amir Abramovich... and Natan S. Kopeika|Show fewer author(s)
We present an inexpensive technique to obtain a three-dimensional (3D) millimeter wave (MMW) and terahertz (THz) image using upconversion. In this work we describe and demonstrate a method for upconversion of MMW/THz radiation to the visual band using a very inexpensive miniature glow discharge detector (GDD) and a silWe present an inexpensive technique to obtain a three-dimensional (3D) millimeter wave (MMW) and terahertz (THz) image using upconversion. In this work we describe and demonstrate a method for upconversion of MMW/THz radiation to the visual band using a very inexpensive miniature glow discharge detector (GDD) and a silicon photodetector. We present MMW/THz upconversion images based on measuring the visual light emitting from the GDD rather than its electrical current. The results show better response time and better sensitivity compared to the electronic detection performed previously. Furthermore, in this work we perform frequency modulation continuous wave (FMCW) radar detection based on this method using a GDD lamp, with a photodetector to measure GDD light emission. By using FMCW detection, the range in addition to the intensity at each pixel can be obtained, thus yielding the 3D image. The GDD acts as a heterodyne mixer not only electronically but also optically. Thesuggested 3D upconversion technique using the GDD is simple and inexpensive and has better performance compared to other MMW/THz imaging systems suggested in the literature. This method provides minimum detectable signal power that is about 6 orders of magnitude better than similar plasma systems due to the very largeinternal signal gain deriving from the much smaller electrode separation and resulting in much higher plasma electric field..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 306 (2016)
Imaging Systems
Fast reconstructed and high-quality ghost imaging with fast Walsh–Hadamard transform
Le Wang, and Shengmei Zhao
In this paper, we propose a ghost imaging scheme with fast Walsh–Hadamard transform, named GIFWHT. In the scheme, Walsh–Hadamard pattern pairs are used to illuminate an object to generate pairs of detection results, and the corresponding differential detection result is used as the result as that from the conventional In this paper, we propose a ghost imaging scheme with fast Walsh–Hadamard transform, named GIFWHT. In the scheme, Walsh–Hadamard pattern pairs are used to illuminate an object to generate pairs of detection results, and the corresponding differential detection result is used as the result as that from the conventional bucket detector. By performing the fast Walsh–Hadamard transform on 2k (k is a positive integer) differential detection results, the image of the object can be recovered. The experimental and numerical simulation results show that the reconstruction time of GIFWHT is greatly reduced, and the quality of the recovered image is noticeably improved. In addition, GIFWHT is robust against interference from environmental illumination and could savememory.Network Technology, Ministry of Education (NYKL2015011)..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 240 (2016)
Integrated Optics
Design of a barcode-like waveguide nanostructurefor efficient chip–fiber coupling
Xiang Wen, Ke Xu, and Qinghai Song
A barcode-like waveguide nanostructure with discretized multilevel pixel lines is designed and optimized by a nonlinear search algorithm. We obtain the design of a one-dimensional multilevel nanostructure with ?1.04 dB efficiency for surface normal coupling to a standard single-mode fiber. Another design is achieved frA barcode-like waveguide nanostructure with discretized multilevel pixel lines is designed and optimized by a nonlinear search algorithm. We obtain the design of a one-dimensional multilevel nanostructure with ?1.04 dB efficiency for surface normal coupling to a standard single-mode fiber. Another design is achieved from the automatic optimization process, which enables polarization-independent coupling to a single-mode fiber. The optimum coupling efficiency is simulated to be ?2.83 dB for TE and ?3.49 for TM polarization centered near the 1550 nm wavelength. Polarization-dependent loss of less than 1 dB over 45.3 nm is achieved..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 209 (2016)
Lasers and Laser Optics
High-peak-power passivelyQ-switched Nd:YAG/Cr4+:YAG composite laser with multiple-beam output
T. Dascalu, G. Croitoru, O. Grigore, and N. Pavel
We report on the design, realization, and output performance of a diode-pumped high-peak-power passively Q-switched Nd:YAG∕Cr4:YAG composite medium onolithic laser with four-beam output. The energy of a laser pulse was higher than 3 mJ with duration of 0.9 ns. The proposed system has the ability to choose independentlWe report on the design, realization, and output performance of a diode-pumped high-peak-power passively Q-switched Nd:YAG∕Cr4:YAG composite medium onolithic laser with four-beam output. The energy of a laser pulse was higher than 3 mJ with duration of 0.9 ns. The proposed system has the ability to choose independently the focus of each beam. Such a laser device can be used for multipoint ignition of an automobile gasoline engine, but could also be of interest for ignition in space propulsion or in turbulent conditions specific to aeronautics..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 267 (2016)
Power-scaled dissipative soliton using double-claddingpumped Yb-doped all-fiber amplifier
Mohamed A. Abdelalim, Hussein E. Kotb, Hanan Anis, and Serguei Tchouragoulov
We report on an all-fiber oscillator followed by an all-fiber amplifier to produce as short as 382 fs laser pulses with up to 0.9Waverage power. The oscillator is an all-normal-dispersion all-fiber dissipative soliton laser operating at 1030 nm, and operating in dissipative soliton mode. The amplifier stage is mainly bWe report on an all-fiber oscillator followed by an all-fiber amplifier to produce as short as 382 fs laser pulses with up to 0.9Waverage power. The oscillator is an all-normal-dispersion all-fiber dissipative soliton laser operating at 1030 nm, and operating in dissipative soliton mode. The amplifier stage is mainly based on a double-cladding 20 μm radius ytterbium-doped fiber pumped by an up to 2.5WCWlaser source. The optical-to-optical conversion amplifier efficiency is around 40%. To our knowledge, this is the first report of an all-fiber mode-locked fiber laser oscillator amplified by an all-fiber amplifier..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 277 (2016)
Midinfrared optical frequency comb based on difference frequency generation using high repetition rate Er-doped fiber laser with single wall carbon nanotube film
M. Tsuzuki, L. Jin, M. Yamanaka, V. Sonnenchein... and N. Nishizawa|Show fewer author(s)
We demonstrated stable midinfrared (MIR) optical frequency comb at the 3.0 μm region with difference frequency generation pumped by a high power, Er-doped, ultrashort pulse fiber laser system. A soliton mode-locked 161 MHz high repetition rate fiber laser using a single wall carbon nanotube was fabricated. The output pWe demonstrated stable midinfrared (MIR) optical frequency comb at the 3.0 μm region with difference frequency generation pumped by a high power, Er-doped, ultrashort pulse fiber laser system. A soliton mode-locked 161 MHz high repetition rate fiber laser using a single wall carbon nanotube was fabricated. The output pulse was amplified in an Er-doped single mode fiber amplifier, and a 1.1–2.2 μm wideband supercontinuum (SC) with an average power of 205 mW was generated in highly nonlinear fiber. The spectrogram of the generated SC was examined both experimentally and numerically. The generated SC was focused into a nonlinear crystal, and stable generation of MIR comb around the 3 μm wavelength region was realized.(AMED)..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 313 (2016)
Self-starting passively mode-locked all fiber laser based on carbon nanotubes with radially polarized emission
Yong Zhou, Jian Lin, Xiaoqiang Zhang, Lixin Xu... and Qiwen Zhan|Show fewer author(s)
We demonstrate an all fiber passively mode-locked laser emitting a radially polarized beam by using a few-mode fiber Bragg grating to achieve mode selection and spectrum filtering. An offset splicing of single-mode fiber with four-mode fiber is utilized as a mode coupler in the laser cavity. Carbon nanotubes are introdWe demonstrate an all fiber passively mode-locked laser emitting a radially polarized beam by using a few-mode fiber Bragg grating to achieve mode selection and spectrum filtering. An offset splicing of single-mode fiber with four-mode fiber is utilized as a mode coupler in the laser cavity. Carbon nanotubes are introduced into the laser cavity as the saturable absorber to achieve self-start mode locking. The laser operates at 1547.5 nm with a narrow spectrum width of 0.3 nm at 30 dB. The emitted mode-locked pulses have a duration of 22.73 ps and repetition of 10.61 MHz. A radially polarized beam has been obtained with high mode purity by adjusting the polarization in the laser cavity..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 327 (2016)
Materials
Thermal and luminescent properties of 2 μm emission in thulium-sensitized holmium-doped silicate-germanate glass
Rong Chen, Ying Tian, Bingpeng Li, Xufeng Jing... and Xianghua Zhang|Show fewer author(s)
In this paper, we present the luminescent properties of Tm3+∕Ho3+ co-doped new glass. A series of silicategermanate glass was prepared by the conventional melt-quenching method. In the Tm3+∕Ho3+ co-doped silicategermanate glass, a strong emission of 2 μm originating from the Ho3+:5I7 → 5I8 transition can be observed unIn this paper, we present the luminescent properties of Tm3+∕Ho3+ co-doped new glass. A series of silicategermanate glass was prepared by the conventional melt-quenching method. In the Tm3+∕Ho3+ co-doped silicategermanate glass, a strong emission of 2 μm originating from the Ho3+:5I7 → 5I8 transition can be observed under conventional 808 nm pumping. The characteristic temperatures, structure, and absorption spectra have been measured. The radiative properties of Ho33+ in the prepared glass were calculated. The emission cross section of Ho33+ ions transition can reach 4.78 × 10?21 cm2 around 2 μm, and the FWHM is as high as 153 nm. The energy transfer efficiency between Ho3+ and Tm3+ has a large value (52%), which indicates the Tm3+∕Ho3+ co-doped silicategermanate glass is a suitable candidate for the 2 μm laser. Moreover, the energy transfer mechanism between Tm3+ and Ho3+ ions was investigated.(61370049, 61308090, 61405182, 51172252, 51372235, 51472225); International Science & Technology Cooperation Program of China (2013DFE63070); Public TechnicalInternational Cooperation Project of the Science Technology Department of Zhejiang Province (2015c340009)..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 214 (2016)
Nonlinear Optics
All-optical two-channel polarization-multiplexing format conversion from QPSK to BPSK signals in a silicon waveguide
Xianglian Feng, Zhihang Wu, Xiaoyan Wang, Sailing He, and Shiming Gao
All-optical two-channel format conversion is proposed and experimentally demonstrated from a 40 Gbit/s polarization multiplexing (Pol-MUX) non-return-to-zero quadrature phase-shift keying (QPSK) signal to Pol-MUX binary phase-shift keying (BPSK) signals by using phase-doubled four-wave mixing effects with two polarizatAll-optical two-channel format conversion is proposed and experimentally demonstrated from a 40 Gbit/s polarization multiplexing (Pol-MUX) non-return-to-zero quadrature phase-shift keying (QPSK) signal to Pol-MUX binary phase-shift keying (BPSK) signals by using phase-doubled four-wave mixing effects with two polarization-angled pumps in a silicon waveguide. The eye diagrams and constellation diagrams of the original QPSK sequences and the converted BPSK sequences of each channel are clearly observed on the two polarization states. Moreover, the bit error rates (BERs) of the two converted idlers are measured. The power penalties of all these converted BPSK sequences on both X and Y polarization states are less than 3.4 dB at a BER of 3.8 × 10?3.(20130101110089); Natural Science Foundation of Zhejiang Province (LY14F050006)..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 245 (2016)
Hybrid silicon slotted photonic crystal waveguides: how does third order nonlinear performance scale with slow light
Junfei Xia, Samuel Serna, Weiwei Zhang, Laurent Vivien, and éric Cassan
We investigate in this paper the influence of slow light on the balance between the Kerr and two-photon absorption (TPA) processes in silicon slotted hybrid nonlinear waveguides. Three typical silicon photonic waveguide geometries are studied to estimate the influence of the light slow-down factor on the mode field oveWe investigate in this paper the influence of slow light on the balance between the Kerr and two-photon absorption (TPA) processes in silicon slotted hybrid nonlinear waveguides. Three typical silicon photonic waveguide geometries are studied to estimate the influence of the light slow-down factor on the mode field overlap with the silicon region, as well as on the complex effective nonlinear susceptibility. It is found that slotted photonic crystal modes tend to focalize in their hollow core with increasing group index (nG) values. Considering a hybrid integration of nonlinear polymers in such slotted waveguides, a relative decrease of the TPA process by more factor of 2 is predicted from nG 10 to nG 50. As a whole, this work shows that the relative influence of TPA decreases for slotted waveguides operating in the slow light regime, making them a suitable platform for third-order nonlinear optics..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 257 (2016)
Ultrafast nonlinear absorption and nonlinear refraction in few-layer oxidized black phosphorus
Shunbin Lu, Yanqi Ge, Zhengbo Sun, Zongyu Huang... and Han Zhang|Show fewer author(s)
We experimentally investigated the nonlinear optical response in few-layer oxidized black phosphorus (OBP) by the femtosecond Z-scan measurement technique, and found that OBP not only possesses strong ultrafast saturable absorption but also a nonlinear self-defocusing effect that is absent in black phosphorus (BP). TheWe experimentally investigated the nonlinear optical response in few-layer oxidized black phosphorus (OBP) by the femtosecond Z-scan measurement technique, and found that OBP not only possesses strong ultrafast saturable absorption but also a nonlinear self-defocusing effect that is absent in black phosphorus (BP). The saturable absorption property originates mainly from the direct band structure, which is still maintained in OBP. The emergence of self-defocusing might originate from the combined consequences of the oxygen-induced defects in BP. Our experimental findings might constitute the first experimental evidence on how to dynamically tuneits nonlinear property, offering an inroad in tailoring its optical properties through chemical modification (oxidation, introducing defects, etc.). The versatile ultrafast nonlinear optical properties (saturable absorption and self-defocusing) imply a significant potential of the layered OBP in the development of unprecedentedoptoelectronic devices, such as mode lockers, optical switches, laser beam shapers, and wavelength converters.China Postdoctoral Science Foundation (2015M580731); Science and Technology Planning Project of Guangdong Province (2016B050501005)..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 286 (2016)
Noise-like pulse generation from a thulium-doped fiber laser using nonlinear polarization rotation with different net anomalous dispersion
Shuo Liu, Fengping Yan, Yang Li, Luna Zhang... and Yafei Hou|Show fewer author(s)
A mode-locked thulium-doped fiber laser (TDFL) based on nonlinear polarization rotation (NPR) with different net anomalous dispersion is demonstrated. When the cavity dispersion is ?1.425 ps2, the noise-like (NL) pulse with coherence spike width of 406 fs and pulse energy of 12.342 nJ is generated at a center wavelengtA mode-locked thulium-doped fiber laser (TDFL) based on nonlinear polarization rotation (NPR) with different net anomalous dispersion is demonstrated. When the cavity dispersion is ?1.425 ps2, the noise-like (NL) pulse with coherence spike width of 406 fs and pulse energy of 12.342 nJ is generated at a center wavelength of 2003.2 nm with 3 dB spectral bandwidth of 23.20 nm. In the experimental period of 400 min, the 3 dB spectral bandwidth variation, the output power fluctuation, and the central wavelength shift are less than 0.06 nm, 0.04 dB, and 0.4 nm, respectively, indicating that the NPR-based TDFL operating in the NL regime holds good long-term stability..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 318 (2016)
Optical Devices
Theory of high-density low-cross-talk waveguide superlattices
Nan Yang, Huashan Yang, Hengrun Hu, Rui Zhu... and Wei Jiang|Show fewer author(s)
Waveguide superlattices, a special type of waveguide arrays, can be designed to achieve very low cross talk at submicrometer/subwavelength pitches. The theoretical framework and design rationales for such waveguide superlattices will be presented in depth. Waveguide sidewall roughness can help to deter the coherent couWaveguide superlattices, a special type of waveguide arrays, can be designed to achieve very low cross talk at submicrometer/subwavelength pitches. The theoretical framework and design rationales for such waveguide superlattices will be presented in depth. Waveguide sidewall roughness can help to deter the coherent coupling between identical waveguides in nearby supercells, but it also induces random fluctuation of transmission. Statistical behavior of the transmission due to roughness in a waveguide superlattice is systematically treated. Complex transmission characteristics due to spectral oscillation and random roughness will be presented, and their evolution with the superlattice length will be analyzed.Institutions..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 233 (2016)
Plasmonics
Low cross-talk, deep subwavelength plasmonic metal/insulator/metal waveguide intersections with broadband tunability
Tae-Woo Lee, Da Eun Lee, Young Jin Lee, and Soon-Hong Kwon
We suggest a low cross-talk plasmonic cross-connector based on a metal/insulator/metal cavity and waveguides. We separately investigate the isolated cavity mode, the waveguide mode, and the combination of cavity and waveguide modes using a finite-different time-domain method. Due to resonant tunneling and the cutoff frWe suggest a low cross-talk plasmonic cross-connector based on a metal/insulator/metal cavity and waveguides. We separately investigate the isolated cavity mode, the waveguide mode, and the combination of cavity and waveguide modes using a finite-different time-domain method. Due to resonant tunneling and the cutoff frequency of the odd waveguide mode, our proposed structure achieves a high throughput transmission ratio and eliminates cross-talk. Furthermore, the proposed structure has a broadband tunability of 587 nm, which can be achieved by modulating the cavity air gap thickness. This structure enables the miniaturization of photonic integrated circuits and sensing applications..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 272 (2016)
Understanding localized surface plasmon resonance with propagative surface plasmon polaritons in optical nanogap antennas
Hongwei Jia, Fan Yang, Ying Zhong, and Haitao Liu
The plasmonic nanogap antenna is an efficient radiating or receiving optical device. The resonance behavior of optical antennas is commonly attributed to the excitation of a localized surface plasmon resonance (LSPR), which can be theoretically defined as the quasi-normal mode (QNM). To clarify the physical origin of tThe plasmonic nanogap antenna is an efficient radiating or receiving optical device. The resonance behavior of optical antennas is commonly attributed to the excitation of a localized surface plasmon resonance (LSPR), which can be theoretically defined as the quasi-normal mode (QNM). To clarify the physical origin of the LSPR, we build up an analytical model of the LSPR by considering a multiple scattering process of propagative surface plasmon polaritons (SPPs) on the antenna arms. The model can comprehensively reproduce the complex eigenfrequency and the field distribution of QNMs of the antenna, unveiling that the LSPR arises from a Fabry–Perot resonance of SPPs. By further applying the complex pole expansion theorem of meromorphic functions, the field of the antenna under illumination by a nearby dipole emitter can be analytically expanded with QNMs, which well predicts the frequency response of the enhancement factor of radiation. The present model establishes explicit relations between the concepts of the LSPR and the propagative SPP and integrates the advantages of the Fabry–Perot and QNM formalisms of nanogap antennas..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 293 (2016)
Remote Sensing and Sensors
Ultrasensitive biosensors based on long-range surface plasmon polariton and dielectric waveguide modes
Leiming Wu, Jun Guo, Hailin Xu, Xiaoyu Dai, and Yuanjiang Xiang
An ultrasensitive biosensor based on hybrid structure and composed of long-range surface plasmon polariton (LRSPP) and dielectric planar waveguide (PWG) modes is proposed. Both PWG and LRSPP modes have strong resonances to form strong coupling between the two modes, and the two modes can couple to enhance sensitivityofAn ultrasensitive biosensor based on hybrid structure and composed of long-range surface plasmon polariton (LRSPP) and dielectric planar waveguide (PWG) modes is proposed. Both PWG and LRSPP modes have strong resonances to form strong coupling between the two modes, and the two modes can couple to enhance sensitivityof sensors. In the hybrid structure, PWG is composed of cytop–Si–cytop multilayers and the LRSPP configuration is composed of cytop–metal–sensing medium multilayer slabs. The highest imaging sensitivities of 2264 and 3619 RIU?1 were realized in the proposed sensors based on Au and Al-monolayer graphene, respectively, which are nearly 1.2 and 1.9 times larger than the 1910 RIU?1 sensitivity of the conventional LRSPR sensor (LRSPP sensor). Moreover, it is demonstrated that the PWG-coupled LRSPP biosensor is applicable to the sensing medium, with refractive index in the vicinity of 1.34.of Guangdong Province (2016B050501005); Science and Technology Project of Shenzhen (JCYJ20140828163633996, JCYJ20150324141711667); Natural Science Foundation ofSZU (201452, 201517, 827-000051, 827-000052, 827-000059)..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 262 (2016)
Sensors
Fiber loop ring-down cavity integrated U-bent single-mode-fiber for magnetic field sensing
Yaofei Chen, Tiegen Liu, Qun Han, Wenchuan Yan, and Lin Yu
A novel magnetic field sensing system based on the fiber loop ring-down technique is proposed in this paper. In the fiber loop, a U-bent single-mode-fiber structure coated with magnetic fluid (MF) serves as the sensing head, and an erbium-doped fiber amplifier (EDFA) is introduced to compensate for the intrinsic loss oA novel magnetic field sensing system based on the fiber loop ring-down technique is proposed in this paper. In the fiber loop, a U-bent single-mode-fiber structure coated with magnetic fluid (MF) serves as the sensing head, and an erbium-doped fiber amplifier (EDFA) is introduced to compensate for the intrinsic loss of the cavity. The ring-down time of the system varies with the change of applied magnetic field due to the tunable absorption coefficient and refractive index of the MF. Therefore, measurement of the magnetic field can be realized by monitoring the ringdown time. The experimental results show that the performance of the system is extremely dependent on the interrogation wavelength, because both the gain of the EDFA and the loss of the sensing head are wavelength dependent. We found that at the optimal wavelength, the ratio of the gain to loss attained its maximum. The sensing system was experimentally demonstrated and a sensitivity of ?0.5951 μs∕Oe was achieved.61107035)..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 322 (2016)
Silicon Photonics
Strip-loaded waveguide-based optical phase shifter for high-efficiency silicon optical modulators
Yuriko Maegami, Guangwei Cong, Morifumi Ohno, Makoto Okano, and Koji Yamada
We propose a novel silicon optical phase shifter structure based on heterogeneous strip-loaded waveguides on a photonic silicon on insulator (SOI) platform. The features of an etchless SOI layer and loaded strip would enhance the performance and uniformity of silicon optical modulators on a large-scale wafer. We implemWe propose a novel silicon optical phase shifter structure based on heterogeneous strip-loaded waveguides on a photonic silicon on insulator (SOI) platform. The features of an etchless SOI layer and loaded strip would enhance the performance and uniformity of silicon optical modulators on a large-scale wafer. We implemented the phase shifter by loading an amorphous silicon strip onto an SOI layer with a vertical PN diode structure. Compared to the conventional lateral PN phase shifter based on half-etched rib waveguides, this phase shifter shows a >1.5 times enhancement of modulation efficiency and provides >20 GHz high-speed operation..
Photonics Research
- Publication Date: Dec. 23, 2016
- Vol. 4, Issue 6, 222 (2016)
© Copyright 2018-2021 | Chinese Laser Press. All Rights Reserved 沪ICP备15018463号-20