Abstract
1 Introduction
Since the first realization of Ti:sapphire pumped Rb vapor laser operating on the resonance at 795 nm by Krupke et al. in 2003[1], diode-pumped alkali vapor laser (DPAL) has become a research focus in the high-power laser field owing to its good beam quality with high output power and efficient energy conversion with excellent thermal management[2–7]. However, the huge spectral mismatch between the pump line of commercial semiconductors and the absorption line of alkali atoms becomes a non-negligible issue encountered in the development of DPAL[8]. A new class of laser device, the exciplex-pumped alkali vapor laser (XPAL), was invented to resolve such a problem. XPAL was first experimentally reported by Readle et al. in 2008[9] while the idea can be dated to 2002[10]. The kinetic processes and lasing properties of XPAL significantly differ from DPAL as the intermedium energy states introduced by the buffer gas not only broaden the atomic resonance line to nanometers, but also directly take part in the optical pump process, promising an efficient use of pump power[9,11]. Owing to these advantages, Palla et al. extended the theoretical studies in detail[11–15], in which the operating mechanism and output performance of XPALs were simulated and predicted. Until now, four-level and five-level XPALs with Cs–Ar, Cs–Kr, Cs–Xe, and Rb–Kr as gain media have been realized in experiments[9,16–19]. However, a sharp radial temperature gradient caused by severe thermal effects will occur in the gain medium during a continuous-wave (CW) operation XPAL, resulting in an uneven distribution of the number density of Cs particles, thereby reducing the output power of the laser[20]. To solve this issue, on the one hand, a multi-pulse pump can be used instead of a CW pump to alleviate the heat loading[21,22]; on the other hand, studies show that longitudinal gas flow at the sonic level is required to control the thermal accumulation in a CW XPAL[23–25], which is difficult to realize in experiment.
In this paper, combining rate equations, heat conduction equations, and fluid heat transfer equations, a three-dimensional exciplex-pumped Cs vapor laser (XPCsL) model is established to study more effective methods on heat dissipation. The effects of pump intensity, wall temperature, and direction and velocity of gas flow on laser output performance are simulated and analyzed, where the three-dimensional distributions of temperature and particle number density of Cs are presented in detail.
2 Description of model
The schematic diagram of the XPAL device is shown in Figure 1. Transverse and longitudinal gas flow XPAL systems are depicted in Figures 1(a) and 1(b), respectively, where the pump light is introduced by the polarization beam splitter (PBS) and oscillates in the resonant cavity formed by the output coupler (OC) and high reflector (HR), and the Cs–Ar mixed gas is filled in a circulating flow structure. As can be seen in Figure 1(c), the cell is divided into small cuboids having a length, width, and height of
Sign up for High Power Laser Science and Engineering TOC. Get the latest issue of High Power Laser Science and Engineering delivered right to you!Sign up now
Figure 1.Sketch of optical systems of XPCsL.
2.1 Kinetic processes of XPAL
The kinetic processes involved in the simulation are presented in Figure 2. The rate equations in each volume element can be written as follows:
Figure 2.Diagram of energy states in high-power XPCsL system.
The rates of laser emission
The pump beam at
The other parameters involved in the rate equations are listed in Table 1.
No. | Process | Cross-section/rate | References |
---|---|---|---|
Thermal associative/dissociative process | |||
1 | |||
[ | |||
2 | |||
Pumping | |||
3 | Equation | ||
Lasing | |||
4 | Equation | ||
Spontaneous emission | |||
5 | |||
[ | |||
6 | |||
Photoexcitation | |||
7 | [ | ||
Energy pooling | |||
8 | [ | ||
Photoionization | |||
9 | [ | ||
Penning ionization | |||
10 | [ | ||
Dissociative recombination | |||
11 | |||
12 | [ | ||
13 |
Table 1. Kinetic processes in the XPAL system.
2.2 Solution for laser power
The propagations of laser and pump lights along the z-axis are described by the following iterative equations:
The initial boundary conditions of
To calculate the output power of the laser, we first assume a laser output power value and then substitute it into the initial equation at z = 0 for iterative operation. If the boundary equation
2.3 Calculation of temperature distribution
The heat generated by multiple transitions in each volume element is given by
2.3.1. Temperature distribution without medium flow
The heat dissipation in the cell is mainly attributed to heat conduction when u = 0, which can be expressed as
2.3.2. Temperature distribution with medium flow
The heat removed in each volume by flowed gases with different direction can be calculated by
On the other hand, the heat transferred by heat conduction in each volume element can be written as
Then the temperature
3 Results and discussion
3.1 Comparison with experimental result
Figure 3 is the comparison of slope efficiency between experiment[19] and simulation results with the parameters listed in Table 2. A laser pulse train with FWHM of 40 ns is used in experiment, generating a
Figure 3.Comparison of slope efficiency between experiment[19] and simulation results.
Length of cell | Temperature | Pressure of Ar | OC ratio |
---|---|---|---|
4 cm | 455 K | 1270 Torr | 0.13 |
Table 2. Parameters of experiment and simulation.
3.2 Three-dimensional distribution of temperature
The temperature distribution in the gain medium can highly influence the output performance especially on the beam quality. Figure 4 presents the three-dimensional distribution of temperature in the cell under conditions of longitudinal and transverse gas flow, where the velocity of flow and wall temperature are both set at 50 m/s and 473 K, respectively. As shown in Figure 4(a), the temperature distribution is circularly distributed and outward diffuses whereas it is elliptically outwardly distributed in Figure 4(b). The maximum temperatures in Figures 4(a) and 4(b) are 831.4 and 495.9 K, indicating an advantage that transverse flow can take in temperature control. On the other hand, comparing Figures 4(a) with 4(b), one can note that the maximum point of temperature in the x–y plane is shifted from (0, 0) to (0.7, 0) when the cooling flow is changed from longitudinal to transverse. Therefore, though the longitudinal gas flow can effectively reduce the temperature overall, it also creates a new temperature gradient in the z-axis direction, whereas the transverse flow avoids this problem by moving the majority of heat away from the optical axis. In general, the transverse gas flow can more effectively control the paraxial temperature, so that improving the operating environment of laser system.
Figure 4.Three-dimensional temperature distribution under different flow directions. The velocity of flow and wall temperature in (a) and (b) are 50 m/s and 473 K.
Figure 5 shows the more detailed distribution of temperature and
Figure 5.(a), (b) The temperature distribution in the
3.3 Influence of flow on optical-to-optical efficiency
In Section 3.2, we confirm that the temperature distribution in the gain medium can affect the output performance of the laser by changing distribution of the number density of Cs particles. Therefore, in this section, we take the maximum temperature as an indicator to characterize the temperature gradient in the cell, and further study the influences of pump intensity, wall temperature, and gas flows with different directions and velocities on the optical-to-optical efficiency. The parameters used in the simulation are listed in Table 3.
Parameters | Definition | Value |
---|---|---|
Length of the cell | 2 cm | |
Cross-section of the cell | 2 mm | |
Pressure of ethane | 1300 Torr | |
OC reflectivity | 0.5 | |
Back mirror reflectivity | 0.99 | |
Single-pass cell window transmission | 0.98 | |
Intra-cavity single-pass loss | 0.9 | |
Waist of the pump beam | 0.5 mm | |
Waist of the laser beam | 0.5 mm |
Table 3. Parameters used in the simulation.
Figure 6 depicts the optical-to-optical efficiency and maximum temperature as a function of flow velocity with different pump intensity at Tw = 473 K. One can see from Figure 6 that severe heat accumulation will occur in the gain medium during the operation without gas flow, which greatly limits the output performance of laser. The optical-to-optical efficiency in Figures 6(a) and 6(b) increases with the rise of flow velocity and pump intensity, and then tends to be saturated, while the maximum temperature in Figures 6(c) and 6(d) is the opposite. In the case of longitudinal gas flow, in the range of 0 to ~50 m/s, the maximum temperature and optical-to-optical efficiency are more sensitive to the change of fluid velocity, whereas that range in Figures 6(b) and 6(d) is 0 to ~10 m/s. In particular, in Figure 6(d), the effect of the fluid velocity on the temperature gradient in the gain medium is relatively small after crossing 20 m/s. Furthermore, the laser output tends to be saturated with a transverse gas flow of ~50 m/s, whereas ~250 m/s of longitudinal gas flow is needed in the same situation.
Figure 6.Optical-to-optical efficiency and maximum temperature as a function of flow velocity with different pump intensity at
On the other hand, compared with Figures 6(a) and 6(c), the slopes of the curves in Figures 6(b) and 6(d) are larger, respectively, indicating that the transverse gas flows have a better heat dissipation efficiency. In addition, under the same conditions, the maximum temperature in the cell is always lower with transverse gas flow, resulting in a higher laser output.
The relationship between optical-to-optical efficiency and flow velocity with different wall temperature at a pump intensity of 5 × 1010 W/m2 is plotted in Figure 7, in which the conclusions obtained in Figure 6 can also be confirmed. In addition, the maximum temperature in Figure 7 rises and is higher than that in Figure 6 when u = 0 as the wall temperature increases. In other words, a higher wall temperature is more likely to generate a larger heat load in the gain medium. In the case of u > 0, the slope of curve representing the maximum temperature decreases significantly after the fluid velocity in Figures 7(c) and 7(d) reaches ~100 m/s and ~20 m/s, respectively. Comparing Figures 7(a) and 7(b) with Figures 6(a) and 6(b), it can be concluded that the wall temperature has a greater contribution to the improvement of optical-to-optical efficiency than the pump intensity. At the same time, a higher wall temperature means a higher flow velocity is required to reach the saturation value of the laser output, which is shown in Figures 7(a) and 7(b): with wall temperature higher than 503 K, longitudinal gas flow of quasi-sonic level and transverse gas flow greater than 50 m/s may be required to alleviate the thermal effect in the cell, maximizing the laser output.
Figure 7.Optical-to-optical efficiency and maximum temperature as a function of flow velocity with different wall temperature at pump intensity of 5 × 1010 W/m2.
4 Summary
In this paper, considering the kinetics, heat conduction, and fluid dynamics processes in the gain medium, we established a comprehensive three-dimensional physical model to simulate and analyze the laser output performance and temperature distribution in an XPCsL with longitudinal and transverse gas flow. The slope efficiency of laser calculated by the model is consistent with the experimental results. The three-dimensional distributions of temperature and number density of Cs particles in the cell with different directions of gas flow are simulated and depicted, demonstrating that the transverse gas flow can more effectively and uniformly alleviate the heat accumulation on the optical axis of pump light and laser, resulting in a higher particle number density of Cs in the cell. Furthermore, influences of pump intensity, wall temperature, and fluid velocity with different directions on maximum temperature in the cell and optical-to-optical efficiency are presented and analyzed in detail. The results indicate that the optical-to-optical efficiency increases with the pump intensity, wall temperature, and flow velocity. Increasing the wall temperature can better improve the potential of laser output than rising the pump intensity. Meanwhile, it will also cause a more significant heat accumulation in the gain medium, where higher-speed gas flow is required to alleviate it. On the other hand, compared with the longitudinal gas flow, the transverse gas flow with a lower velocity can more effectively remove the generated heat accumulation and reduce the temperature gradient in the cell to enhance the laser output. This work is of great help in revealing the kinetic and fluid dynamic mechanism and output characteristics in an XPCsL and promoting the realization of a high-efficiency fluid XPCsL.
References
[1] W. F. Krupke, R. J. Beach, V. K. Kanz, S. A. Payne. Opt. Lett., 28, 2336(2003).
[2] W. F. Krupke, R. J. Beach, V. K. Kanz, S. A. Payne. Proc. SPIE, 5334, 156(2004).
[3] B. Zhdanov, R. Knize. Proc. SPIE, 8187, 818707(2011).
[4] T. Ehrenreich, B. Zhdanov, T. Takekoshi, S. P. Phipps, R. J. Knize. Electron. Lett., 41, 415(2005).
[5] B. Zhdanov, C. Maes, T. Ehrenreich, A. Havko, N. Koval, T. Meeker, B. Worker, B. Flusche, R. J. Knize. Opt. Commun, 270, 353(2007).
[6] A. V. Bogachev, S. G. Garanin, A. M. Dudov, V. A. Yeroshenko, S. M. Kulikov, G. T. Mikaelian, V. A. Panarin, V. O. Pautov, A. V. Rus, S. A. Sukharev. Quantum Electron, 42(2012).
[7] G. Pitz, G. Hager, T. Tafoya, J. Young, G. Perram, D. Hostutler. Proc. SPIE, 8962, 896208(2014).
[8] G. A. Pitz, C. D. Fox, G. P. Perram. Phys. Rev. A, 82(2010).
[9] J. D. Readle, C. J. Wagner, J. T. Verdeyen, D. L. Carroll, J. G. Eden. Electron. Lett., 44, 1466(2008).
[10] R. V. Markov, A. I. Plekhanov, A. M. Shalagin. Phys. Rev. Lett., 88(2002).
[11] A. D. Palla, D. L. Carroll, J. T. Verdeyen, M. C. Heaven. Proc. SPIE, 7915, 79150B(2011).
[12] A. D. Palla, D. L. Carroll, J. T. Verdeyen, J. D. Readle, T. M. Spinka, C. J. Wagner, J. G. Eden, M. C. Heaven. Proc. SPIE, 7581(2010).
[13] D. L. Carroll, A. D. Palla, J. T. Verdeyen. Proc. SPIE, 8677, 86770J(2013).
[14] A. D. Palla, J. T. Verdeyen, D. L. Carroll. Proc. SPIE, 7751, 77510F(2010).
[15] D. L. Carroll, J. T. Verdeyen. J. Phys. B, 46(2013).
[16] J. D. Readle, J. T. Verdeyen, J. G. Eden, S. J. Davis, K. L. Galbally-Kinney, W. T. Rawlins, W. J. Kessler. Opt. Lett., 34(2009).
[17] J. D. Readle, C. J. Wagner, J. T. Verdeyen, D. L. Carroll, J. G. Eden. Proc. SPIE, 7196, 71960D(2009).
[18] A. E. Mironov, D. L. Carroll, J. W. Zimmerman, J. G. Eden. Appl. Phys. Lett., 113(2018).
[19] M. Endo, T. Nagai, F. Wani. Proc. SPIE, 8677, 867716(2013).
[20] X. Xu, B. Shen, C. Xia, B. Pan. IEEE J. Quantum Electron., 53(2017).
[21] C. Su, B. Shen, X. Xu, C. Xia, B. Pan. High Power Laser Sci. Eng., 7(2019).
[22] C. Su, X. Xu, J. Huang, B. Pan. Opt. Express, 28(2020).
[23] X. Xu, B. Shen, J. Huang, C. Xia, B. Pan. J. Appl. Phys., 122(2017).
[24] X. Xu, B. Shen, J. Huang, C. Xia, B. Pan. Opt. Express, 25(2017).
[25] J. Huang, C. Xia, X. Xu, C. Su, B. Pan. Opt. Express, 27(2019).
[26] K. Waichman, B. D. Barmashenko, S. Rosenwaks. J. Opt. Soc. Am. B, 31(2014).
[27] M. A. Mahmoud, Y. Gamal. Opt. Appl., 40, 129(2010).
[28] B. D. Barmashenko, S. Rosenwaks. J. Opt. Soc. Am. B, 30(2013).
Set citation alerts for the article
Please enter your email address