Evolution Law of Laser-Textured Microstructure on Ni-Co-Si3N4 Composite Coating Surface

Lingling Ji; Ninghui Li; Min Kang

doi:10.3788/LOP202158.0914002

[1] Feng X J, Kan H M, Wei X D et al. Research progress of Ni-based composite coatings prepared by electrodeposition[J]. Surface Technology, 46, 75-82(2017).

[2] Liu L, Kang M, Yang Y C et al. Effect of spray parameters on hardness and wear resistance of Ni-P-BN‍(h)‍-Al2O3 composite coatings[J]. Materials Protection, 53, 93-98,111(2020).

[3] Zhang Y, Kang M, Fu X Q et al. Surface structure and wear resistance of Ni-Co-P-BN(h)-Al2O3 binary nano composite coatings[J]. Materials Science and Technology, 27, 55-66(2019).

[4] Li H Z, Kang M, Zhang Y et al. Influences of jet parameters on structure and wear resistance of Ni-Co-BN‍(h) nanocomposite coatings[J]. China Surface Engineering, 31, 103-112(2018).

[5] Mbugua N S, Kang M, Zhu J P et al. Synthesis and characterization of Ni-W/Cr2O3 nanocomposite coatings using electrochemical deposition technique[J]. Coatings, 9, 815(2019).

[6] Paydar S, Jafari A, Bahrololoom M E et al. Enhancing Ni electroplated matrix through mixed boron nitride-carbide reinforcement[J]. Vacuum, 92, 52-57(2013).

[7] Li N H, Mou L Q, Li Z W et al. Evolution of surface topography of 304L stainless steel irradiated by long pulse laser[J]. AIP Advances, 8, 075211(2018).

[8] Bao Y M, Wang C W, Jin Z W et al. Textured surface on a bioceramic coating via a femtosecond laser and its friction and wear properties[J]. Chinese Journal of Lasers, 46, 0203003(2019).

[9] Ye Y X, Liu Y F, Du T T et al. Experimental study on gradient wettable surface fabricated by laser rapid processing[J]. Chinese Journal of Lasers, 46, 1002001(2019).

[10] Wang L, Wang X S, Li N H et al. Processing of microstructures on 304L stainless steel surface based on long pulse laser[J]. Laser & Optoelectronics Progress, 54, 031402(2017).

[11] Liu C H, Zhu X J, Li X M et al. Wettability of nanosecond laser-induced titanium oxide alloys and coatings[J]. Laser & Optoelectronics Progress, 57, 011408(2020).

[12] Li J, Zhao Y H, Yu H D et al. Fabrication of coupling structure and composite properties by electro-brush plating and laser processing[J]. Journal of Materials Engineering, 44, 28-34(2016).

[13] Li J, Zhao Y H, Yu H D et al. Fabrication and properties of superhydrophobic surface on aluminum alloys substrates by brush plating and laser processing technology[J]. China Mechanical Engineering, 28, 82-87,92(2017).

[14] Li J, Zhao S C, Du F et al. Fabrication of groove and grid structure surface with superhydrophobicity and corrosion resistance by laser[J]. Journal of Materials Engineering, 46, 86-91(2018).

[15] Zhou L P. Study on the texture processing and micro-friction performance of Ni-Co alloy coating[D], 67(2014).

[16] Wan Y, Li J L, Xiong D S et al. Effect of number of laser pulses on tribological property of textured-coating[J]. Laser & Optoelectronics Progress, 54, 031403(2017).

[17] Li T T, Sun Y N, Zhang L et al. Research progress on effect of surface texturing on tribological properties[J]. Materials for Mechanical Engineering, 44, 44-48(2020).

[18] Liu Y, Li X L, Jin J F et al. Anti-icing property of bio-inspired micro-structure superhydrophobic surfaces and heat transfer model[J]. Applied Surface Science, 400, 498-505(2017).

[19] Bennett T D, Krajnovich D J, Grigoropoulos C P et al. Marangoni mechanism in pulsed laser texturing of magnetic disk substrates[J]. Journal of Heat Transfer, 119, 589-596(1997).

[20] Fu Y H, Huang T, Ye Y X et al. Influence of melt flow characteristics on textured bump forming[J]. Chinese Journal of Lasers, 46, 0702005(2019).

[21] Cheng J, Perrie W, Sharp M et al. Single-pulse drilling study on Au, Al and Ti alloy by using a picosecond laser[J]. Applied Physics A, 95, 739-746(2009).

[22] Li N H, Li Z W, Kang M et al. Numerical simulation and experimental study on laser micromachining of 304L stainless steel in ambient air[J]. International Journal of Heat and Mass Transfer, 140, 978-991(2019).

[23] Chen S C, Cahill D G, Grigoropoulos C P. Melting and surface deformation in pulsed laser surface micromodification of Ni-P disks[J]. Journal of Heat Transfer, 122, 107-112(2000).

[24] Sahoo P, Debroy T, McNallan M J. Surface tension of binary metal:surface active solute systems under conditions relevant to welding metallurgy[J]. Metallurgical Transactions B, 19, 483-491(1988).

[25] Lee J, Shimoda W, Tanaka T. Surface tension and its temperature coefficient of liquid Sn-X (X=Ag, Cu) alloys[J]. Materials Transactions, 45, 2864-2870(2004).

[26] Semak V V, Knorovsky G A, MacCallum D O et al. Effect of surface tension on melt pool dynamics during laser pulse interaction[J]. Journal of Physics D, 39, 590-595(2006).

[27] Han S W, Cho W I, Na S J et al. Influence of driving forces on weld pool dynamics in GTA and laser welding[J]. Welding in the World, 57, 257-264(2013).

[28] Stauter C, Fontaine J, Engel T. Real-time determination of the amount of removed material during short pulses laser micromachining[J]. Applied Surface Science, 97, 522-527(96).

[29] Cristoforetti G, Legnaioli S, Palleschi V et al. Observation of different mass removal regimes during the laser ablation of an aluminium target in air[J]. Journal of Analytical Atomic Spectrometry, 23, 1518-1528(2008).

[30] Bindhu C V, Harilal S S, Tillack M S et al. Laser propagation and energy absorption by an argon spark[J]. Journal of Applied Physics, 94, 7402-7407(2003).

[31] Chen X, Wang F, Wu Q et al. Pit morphology evolution law of 3A21 aluminum alloy surface in laser texturing[J]. Laser & Optoelectronics Progress, 56, 241404(2019).