Abstract
1 Introduction
The emergence of ultrafast laser pulse generation, a milestone in laser science, has triggered incredible progress across a wide array of disciplines, encompassing industrial applications, energy technologies, life sciences, and beyond.1,2 Cutting-edge innovations, such as robust laser ignition systems,3 vibrant laser 3D printing,4 mind-boggling attosecond science,5 and high-resolution microscopic imaging,6 are effectively powered by ultrafast lasers. Among the various laser platforms that have been developed, fiber oscillators, esteemed for their compact design, outstanding performance, and cost-effectiveness, have become one of the mainstream technologies for generating femtosecond laser pulses.7
Visible femtosecond lasers stand as pivotal light sources, offering distinct advantages in special material precision processing, high-resolution fluorescence microscopy, optical atomic clocks, and other applications.15
Currently, the majority of visible fiber lasers leverage rare-earth-doped fluoride fibers (e.g., ,24,25,26 and 27) as the efficient gain medium. Over the years, significant progress has been made in achieving wavelength-tunable,28
Sign up for Advanced Photonics Nexus TOC. Get the latest issue of Advanced Photonics Nexus delivered right to you!Sign up now
In this paper, we present an experimental demonstration of a visible-light mode-locked femtosecond fiber oscillator based on a high-gain -doped fiber and a pair of customized diffraction gratings for dispersion management. The oscillator achieves remarkably stable self-starting mode locking, building upon the phase-biased NALM, yielding laser pulses with a central wavelength of 635.5 nm, a widest 3-dB bandwidth of 5.4 nm, a minimum pulse duration of 196 fs, and a repetition rate of 53.957 MHz. By manipulating the intracavity dispersion and polarization, we have observed multiple mode-locking states, including conventional solitons, dispersion-managed solitons, dissipative solitons, and bound-state solitons. To further enhance the laser performance to fulfill more general application purposes, we have constructed a visible chirped-pulse amplification (CPA) system and improved the average power while maintaining a compressed pulse duration of 230 fs. This laser architecture with dispersion management capabilities thus serves as a testbed to explore complex ultrafast soliton dynamics in the visible-wavelength region and paves the way for implementing miniaturized visible fiber femtosecond laser sources with broader spectral range, narrower pulse width, and higher power, enabling a wide range of applications.
2 Experimental Setup and Operation Principle
Figure 1 shows a detailed schematic of the visible-wavelength femtosecond fiber oscillator and amplifier system. The fiber used in the oscillator is a 2.3-m double-clad (DC) -doped fluoride fiber, which is manufactured by Le Verre Fluoré and boasts the following specifications: a doping concentration of 8000 ppm (wt.), a core diameter of , a core numerical aperture (NA) of 0.08, an inner-clad profile in a double D-shaped configuration with dimensions of by , an inner-clad NA of 0.45, an inner-clad absorption coefficient of at 443 nm, a core group velocity dispersion (GVD) coefficient () of at 635 nm, and a core nonlinear coefficient () of . The gain fiber is efficiently pumped directly by a 443 nm laser diode (LD) through a collimator, generating a strong red-light gain. The transition diagram is as below: (1) level is excited by ground state absorption of the level with the 443 nm LD, (2) nonradiative relaxation ensues from to , and (3) radiative transition occurs from to , generating strong emission at .34 Other important components of the oscillator include a homemade dichroic mirror (DM), five wavelength plates, a polarization beam splitter (PBS), a homemade 10:90 beam splitter (BS), a Faraday rotator (FR), and a homemade high-reflective coating mirror. The coating mirrors (DM, BS, and mirror) are manufactured by coating on fused quartz substrates with dielectric films using an ion beam-assisted deposition system (DJ-800, Golden Vacuum). We have also customized a pair of visible transmission gratings with high efficiency ( at 635 nm) and high groove density (1739.1 lines/mm) to minimize the cavity loss and manage total dispersion. The gratings operate near the Littrow configuration, featuring an incident angle of , and providing a GVD coefficient of at 635 nm. The intracavity net dispersion is calculated to be with a grating spacing of 21 mm. The red laser obtained from one collimator accumulates an additional phase shift after traversing the phase shifter comprising the FR and eighth-wave plate twice, and then enters the other collimator, thereby facilitating self-starting mode locking at a low threshold.10 The gratings are introduced strategically to regulate intracavity dispersion for initiating different mode-locking operations (e.g., conventional soliton, dispersion-managed soliton, and dissipative soliton). Furthermore, the oscillator incorporates two half-wave plates and two quarter-wave plates to fine-tune intracavity polarization. It is essential to note that to achieve stable mode-locking operation in the few-mode gain fiber, loops with a radius of are placed on both sides of the fiber to suppress higher-order modes (see the inset of Fig. 1), which bring very little additional loss to the fundamental mode. To further obtain a high-power visible femtosecond laser, the output laser of the oscillator is amplified by the visible CPA system. The system comprises a 2.5 m DC -doped fluoride fiber, a 433 nm LD, a DM, two collimators, and a grating pair compressor. The compressor includes a D-shaped mirror, a hollow roof prism mirror (HRPM), and a pair of transmission gratings with a groove density of 1398.6 lines/mm. In the experiment, the optical spectrum is captured using a 350 to 1750 nm optical spectrum analyzer with a resolution of 0.05 nm (AQ-6315E, Ando). The pulse train and radio-frequency (RF) spectrum are recorded by a 12.5-GHz photodetector (ET-4000F, Electro-Optics Technology, Inc.) in conjunction with a 12-GHz, oscilloscope (DSO81204A, Agilent Infiniium), or an electrical spectrum analyzer (N9020A, Agilent). The pulse duration is determined by an autocorrelator (FR-103XL, Femtochrome), and the power measurements are conducted using a 350 to 1100 nm optical power meter (S142C, Thorlabs, Inc.). In addition, a DM is also used to filter out the remaining pump power (443 nm) when measuring the output laser power of the PBS.
Figure 1.Schematic of visible femtosecond fiber oscillator and amplifier. The inset shows the photograph of the visible femtosecond fiber oscillator. DM, dichroic mirror; HWP, half-wave plate; QWP, quarter-wave plate; EWP, eighth-wave plate; PBS, polarization beam splitter; BS, beam splitter; FR, Faraday rotator; Gratings, a pair of transmission gratings; Mirror, high-reflective coating mirror; DSM, D-shaped mirror; HRPM, hollow roof prism mirror.
3 Results and Discussion
3.1 Visible Femtosecond Fiber Oscillator
In the experiment, the threshold of the continuous-wave (CW) laser is . As the pump power is incrementally raised to 1.63 W, a notable transition occurs where self-starting mode-locking pulses can be observed in the oscilloscope. At this stage, the mode-locked pulse exhibits a multipulse operation, and the transition to stable single-pulse mode locking is achieved by reducing the pump power accordingly. Figure 2 shows the typical output characteristics of the red-light mode-locked femtosecond fiber oscillator under 1.33 W pump power. As shown in Fig. 2(a), the mode-locked optical spectrum manifests a central wavelength of 635.5 nm, accompanied by a 3-dB bandwidth of 4.1 nm. Figure 2(b) gives the typical pulse train with a pulse interval of 18.5 ns, and their pulses have uniform pulse intensity, as evidenced by the inset in Fig. 2(b), underscoring the exceptional stability of the mode-locking operation. Figure 2(c) shows the intensity autocorrelation trace of the output pulses, aptly fitted by a function, revealing a pulse duration as short as 199 fs. In addition, as shown in Fig. 2(d), the output RF spectrum has a fundamental frequency of 53.957 MHz and a high signal-to-noise ratio of . What the inset of Fig. 2(d) shows is particularly noteworthy, as it demonstrates the absence of spectral modulation within the 3 GHz-span RF spectrum, which serves as a compelling testament to the stable mode locking of the oscillator. In addition, the beam quality parameter () of the output laser was measured to be 1.43 and 1.47, indicating the oscillator is almost a single-mode operation.
Figure 2.Typical characteristics of visible mode-locked femtosecond fiber oscillator under the dispersion of
To better understand the mode-locking behavior of the fiber oscillator, the mode-locked evolution with different pump powers is further investigated. Figure 3(a) shows the progression of the optical spectrum versus the pump power. One can, interestingly, see that when the pump power increases, the spectral bandwidth emerges according to the law of recurrent broadening and decreasing. This intriguing behavior could potentially be attributed to the splitting of time-domain pulses into the bound-state pulses with the increase of the pump power [see Fig. 3(b)]. Figure 3(b) also reveals that the temporal separation of the bound-state pulses is about 18.9 ps, corresponding to the spectral modulation of 0.071 nm. It is worth noting that this spectral modulation remains undetected in the spectra due to the low resolution (0.05 nm) of the optical spectrum analyzer. To gain further insights, we meticulously documented the corresponding narrow-range autocorrelation traces (i.e., single-pulse envelope), as shown in Fig. 3(c). Remarkably, under a 1.28 W pump power, an impressive minimum pulse duration of 196 fs is achieved. Furthermore, the pulse duration of these single pulses shows the same trend as the spectral bandwidth, with the pump power incrementally increasing. The results are also interesting and critical, as they show the potential to explore complex soliton dynamics with this simple cavity via power and polarization adjustment.
Figure 3.Evolution of visible femtosecond fiber oscillator with different pump powers under the dispersion of
Figure 4(a) offers the average output power of the 635 nm femtosecond laser concerning the pump power. Both the average output power of the BS (output 1) and the PBS (output 2) exhibits a linear increase without any saturation. Impressively, under a pump power of 2.23 W, we achieved maximum output powers of 11.5 and 120 mW for the BS and PBS, respectively. In addition, under a pump power of 1.48 W, the output powers are 4.2 and 41 mW for the BS and PBS, respectively, with calculated single-pulse energies of 0.078 and 0.76 nJ. Figure 4(a) also shows the oscillator works in single-pulse mode locking within the pump power range of 1.28 to 1.63 W, and as the pump power further increases, the operation becomes bound-state mode locking (also see Fig. 3). To assess the operational stability of the mode-locked femtosecond fiber oscillator, as shown in Fig. 4(b), we recorded the output powers and optical spectra over 40 min under a pump power of 1.53 W. Notably, the RMSEs in both BS and PBS output are 0.01 and 0.12 mW, and the corresponding fluctuations are 0.26% and 0.23%, respectively, illustrating the outstanding stability of the oscillator. In addition, as shown in Fig. 4(c), both the central wavelength and spectral bandwidth of the oscillator remained remarkably stable during the entire 40-min test, displaying no discernible drift or changes, which also indicates the excellent long-term stability of the oscillator. Finally, the relative intensity noise (RIN) is also measured by an RF spectrum analyzer (N9020A, Agilent) together with a Si photodetector (PDA36A2, Thorlabs) for Fourier frequency. The observed RIN shows a floor between and for low frequencies, which is attributed to the instability of free-space components and the power and frequency fluctuations of the pump laser.
Figure 4.Output characterization of 635 nm femtosecond fiber laser oscillator under the dispersion of
In addition, the pulse duration of the mode-locked laser is intricately linked to the net dispersion, which can be finely controlled by regulating the spacing of the intracavity gratings. In our experiment, we systematically explored the influence of various net dispersion regimes on the mode-locking performance by tuning the grating pair interval under a pump power of 1.33 W. The outcomes are presented in Fig. 5 (also see Video 1). Figures 5(a) and 5(b) show a comprehensive view of the optical spectra and the corresponding autocorrelation traces from the output of BS (output 1). When the net dispersion is adjusted to , a broadest spectral 3-dB bandwidth of 5.4 nm along with a pulse duration of 900 fs can be achieved. The spectral bandwidth of 5.4 nm supports the Fourier transform limit duration of for a pulse. Notably, when the net dispersion is set to , we attain the narrowest pulse duration of 199 fs, accompanied by a spectral bandwidth of 4.1 nm, and the time-bandwidth product (TBP) is calculated as 0.61, close to the Fourier-transform limit of a pulse. Turning our attention to the output of the PBS (output 2), as shown in Figs. 5(c) and 5(d), we observe a similar trend in spectral bandwidth with varying net dispersion. Specifically, the obtained widest spectral bandwidth is also at , which is like the output of the BS. Intriguingly, the minimum pulse duration is realized at a net dispersion of , corresponding to a pulse duration of 460 fs, and the TBP is calculated as 0.62. It can also be seen from Fig. 5(d) that with the net dispersion from to , the TBP of the mode-locked laser output from the PBS shows a decreasing trend. Besides, it is noteworthy that adjusting the net dispersion to either large net-anomalous or net-normal values results in a narrowing of the spectral bandwidth, as is evident in Figs. 5(a) and 5(c). Specifically, when the net dispersion is set to (pink curve) and (red curve), the mode-locked spectra exhibit the typical peculiarities of traditional soliton and dissipative soliton, respectively. These findings underscore the versatility of the oscillator in tailoring its output characteristics through precise control of net dispersion, offering opportunities for customizing laser performance for specific applications.
Figure 5.Characteristics of visible fiber oscillator under different net dispersions at 1.33 W pump power. (a) Optical spectra output from the BS (output 1), and (b) the corresponding autocorrelation traces. (c) Optical spectra output from the PBS (output 2), and (d) the corresponding autocorrelation traces (
3.2 Visible Chirped-Pulse Amplification
Subsequently, in the pursuit of high-power visible femtosecond laser output, a visible CPA system was used to amplify the output laser pulses generated by the oscillator. To optimize the amplification process and mitigate nonlinear effects and amplified spontaneous radiation, we strategically selected the laser pulses originating from the PBS output, characterized by a net dispersion of , as the seed laser. This choice was driven not only by its highest output power but also by its relatively wide spectral bandwidth (meaning the potential for duration compression), also considering that dissipative soliton is suitable to achieve larger pulse energy. In the experiment, the laser pulses emanating from the oscillator undergo stretching from 2.6 to 8.6 ps when traversing the 2.5 m DC -doped fluoride fiber and then are subjected to amplification by the red-light fiber amplifier. Subsequently, the amplified laser pulses are compressed through the grating pair compressor. The results of this amplification and compression are shown in Fig. 6. Figure 6(a) gives the amplified spectra under different pump powers. Notably, the spectral bandwidth narrows as the pump power increases, which is attributed to gain narrowing within the amplifier. Impressively, this amplification process yields a maximum average power of 1055 mW, and the corresponding pulse energy is counted as 19.55 nJ, as shown in Fig. 6(b). Furthermore, the grating pair compressor effectively dechirps the pulse duration to 230 fs, as showcased in Fig. 6(c). There is no doubt that higher power is available through more stages of amplification. These results also underscore the efficacy of the visible CPA system in significantly boosting the power of the visible femtosecond laser while maintaining excellent pulse quality, making it a valuable tool for various applications, such as materials processing, biomedical research, and nonlinear optics.
Figure 6.Characteristics of visible fiber CPA. (a) Optical spectra under different pump powers. (b) Amplified average power and pulse energy versus the pump power. (c) Autocorrelation traces before and after amplification.
4 Conclusion
In summary, we successfully demonstrated a 635 nm soliton mode-locked femtosecond fiber oscillator built upon the phase-biased NALM. This oscillator achieves remarkably stable self-starting mode locking, which delivers laser pulses with a central wavelength of 635.5 nm, a broadest 3-dB bandwidth of 5.4 nm, a minimum pulse duration of 196 fs, and a repetition rate of 53.957 MHz. With the precise tuning of the intracavity gratings, we can easily manipulate the cavity in anomalous, near-zero, and normal dispersion regimes. The dispersion management in this manner not only offers the opportunity to study the fruitful soliton dynamics in the visible range but also allows versatile control over laser parameters, such as pulse duration and spectral bandwidth. By implementing a chirped-pulse fiber amplification system, we further promote the laser output from the oscillator to an unprecedented power exceeding 1 W in the visible fiber lasers while maintaining excellent pulse quality. The achieved laser source could already find enormous applications ranging from advanced materials processing to biomedical and nonlinear optics. Due to the exceptional heat dissipation of fibers, the whole laser system operates with excellent long-time stability, characterized by a low power deviation of and negligible wavelength drift. Our soliton mode-locked fiber oscillator and amplifier system bridges the gap in sourcing femtosecond laser pulses from visible fiber lasers, marking a substantial breakthrough in the realm of ultrafast laser technology. This architecture, featuring by compact design, high-performance output, reliable operation, and flexible tunability, can be readily implemented to broaden the mode-locking spectral range, covering the entire visible spectrum. We anticipate immediate applications and stimulation to further activities of such femtosecond fiber laser systems in scientific research, medicine, and biological imaging.
Jinhai Zou received his BS degree in optoelectronic information science and engineering from China Jiliang University in 2017 and his PhD in electronic science and technology from Xiamen University in 2022. His research focuses on fiber lasers in the visible waveband.
Qiujun Ruan received his BS degree in optoelectronic engineering from Huaqiao University in 2014 and his PhD in electronic science and technology from Xiamen University in 2023.
Zhengqian Luo received his BS degree in applied physics from Harbin Institute of Technology in 2004 and his PhD in electrical engineering from Xiamen University in 2009. From 2007 to 2009, he studied at Nanyang Technological University as a joint PhD student. He joined Xiamen University as a faculty member in 2010. From 2016 to 2017, he was a visiting professor at the Massachusetts Institute of Technology. Since 2017, he has been a full professor at Xiamen University and currently serves as the head of the Electronic Engineering Department of Xiamen University. His research focuses on ultrafast fiber lasers and on-chip photonic devices. He has published more than 150 journal or conference papers with a total citation of >5500. He is a recipient of the National Science Fund for Excellent Young Scholars and the Fujian Youth Science and Technology Award. He is a senior member of IEEE and served as a young editorial board member for Chinese Laser Press.
Biographies of the other authors are not available.
References
[1] M. E. Fermann, I. Hartl. Ultrafast fibre lasers. Nat. Photonics, 7, 868-874(2013).
[3] D. Graham-Rowe, R. Won. Lasers for engine ignition. Nat. Photonics, 2, 515-517(2008).
[5] P. Á. Corkum, F. Krausz. Attosecond science. Nat. Phys., 3, 381-387(2007).
[8] Z. Sun et al. Graphene mode-locked ultrafast laser. ACS Nano, 4, 803-810(2010).
[19] A. D. Ludlow et al. Optical atomic clocks. Rev. Mod. Phys., 87, 637-701(2015).
[36] E. Kifle et al. Deep-red double-clad fiber laser at 717 nm. Opt. Lett., 48, 1494-1497(2023).
[46] M.-P. Lord et al. Visible femtosecond fiber laser. Opt. Lett., 48, 3709-3712(2023).
Set citation alerts for the article
Please enter your email address