Abstract
Introduction
The plume temperature of a solid rocket motor is one of the critical parameters to characterize the condition and the combustion state of solid propellant. Accurately measuring the plume temperature of the solid rocket motor is vital to the reference value for understanding the internal combustion condition and the overall performance of the motor[
With the development of laser and spectroscopy, the laser spectroscopy technology is gradually applied to the measurement of the combustion of solid propellant and exhaust plume temperature. For example, the coherent anti-stokes Raman scattering technique (CARS), the temperature of solid propellant can be determined by measuring the anti-stokes light generated by incident excitation laser and stokes laser that through the region[
For measuring of multi-phase combustion, a strong self-radiation plume of the solid rocket motor, there exists a temperature measurement named radiation thermometry. This method can be realized based on the analysis of the flame radiation varying with temperature and composition and characteristics. It is a passive measurement method showing the advantages of wide temperature range, fast response, high reliability and so on. Notably, it has the characteristics of a high signal-to-noise ratio for the spontaneous emission from propellant combustion[
In this paper, firstly, the radiation spectroscopy thermometry was used for solid rocket motor plume temperature measurement based on the above research. Secondly, the exhaust plume flame radiation spectrum measurement system was built to carry out the standard ϕ118 solid rocket motor ground test plume radiation spectrum measurement. Thirdly, the solid rocket motor plume radiation spectrum characteristics were analyzed, and the plume flame gray body characteristics were discussed.Finally, the online measurement of solid rocket motor plume temperature was realized, and the related experimental research was carried out.
1 Principle of measurement
The basic principle of radiation spectroscopy thermometry measurement method is Planck’s radiation law, which describes the variation of radiation intensity with wavelength[
(1)
where ε is the average blackness of high-temperature particles in the detection band, T is the average temperature of the field of view in the detection area, C1=3.742×10-16 W·m2 is the first radiation constant, C2=1.438 8×10-2 m·K is the second radiation constant. When λT≤2 000 μm·K, Planck’s law can be simplified into Wien’s relation
(2)
Therefore, according to the least square method, the optimal function matching of data is found by minimizing the sum of squares of errors, and the objective function f(ε',t) is established
(3)
where ε'=lnε, t=1/T, yi is the logarithm of the radiation intensity corresponding to wavelength measured in the experiment. When f(ε',t) reaches the minimum value, the value of ε' and t is the parameter to be obtained by using the curve fitting of the least square method. Therefore,ε and T the average blackness of the field of view and the average temperature of the field of view can be obtained.
Figure 1.Schematic of radiation spectroscopy thermometry
2 Experimental calibration of spectrometer response coefficient
Optical fiber spectrometer (ISUZU OPTICS, SE1040, 350~1 000 nm, 0.4 nm)is used to measure the plume radiation spectrum of solid rocket motors. Since the spectrometer uses silicon as the photosensitive detection element, the response of the radiant light to the flame of different wavelengths is different to some extent. Therefore, it is necessary to calibrate the response coefficient of the spectrometer by using the standard radiation blackbody furnace to obtain the curve of the response coefficient changing with the wavelength. This curve can be used as the plume radiation spectral data correction, so as to obtain a more accurate plume radiation spectrum.
Assuming that the response intensity value of each pixel of the photosensitive element in the optical fiber spectrometer is linear to the radiant light flux of any single wavelength, it can be found that the actual response intensity value of the photosensitive element to the radiant light
(4)
Where Iλ is the actual response strength walue of the photosensitive element, Aλ is the radiant flux of a single wavelength detected by a photosensitive element, kλ is wavelength response coefficient.
The standard blackbody radiation furnace can be approximated as blackbody radiation.Through the Planck radiation law, temperature blackbody radiation with the change of wavelength can be determined through theoretical calculation. Based on this standard, the change of the spectral response coefficient with the wavelength can be obtained by comparing the experimental spectrum with the theoretical spectrum of blackbody radiation. The response coefficient characteristics of the spectrometer were obtained by using the blackbody furnace. (FuYuan Optoelectronics, HFY-203b, 0.99, 1 423 K). The response coefficient characteristics of the spectrometer are shown in Fig.2. It can be seen that the response value of the spectrometer is not linear with the wavelength, which is mainly influenced by the characteristics of the factory standard light source. The selection of response coefficient and parameter fitting wavelength range is mainly based on the spectral signal-to-noise ratio, spectral linear response and spectral characteristics. In the wavelength range of 675~745 nm, the wavelength response coefficient is relatively stable, and the linearity is good. Therefore, this spectral range is selected as the parameter fitting range of the radiation spectral temperature measurement method. Through the modification of the above standard radiation calibration, a more accurate high-temperature flame radiation spectrum can be obtained and the temperature measurement accuracy of radiation spectroscopy can be effectively improved.
Figure 2.Spectrometer wavelength response curve
3 Experimental measurement system and experimental conditions
Fig.3 shows the schematic diagram of the experimental system for measuring the temperature of the solid rocket plume radiation spectrum. The system consists of the standard ϕ118 solid rocket motor, focusing lens, optical fiber probe, and optical fiber spectrometer. The radiation spectrum of the exhaust plume is gathered to the optical fiber probe by a concentrator lens, and the optical fiber probe receives the flame radiation light and transmits it to the optical fiber spectrometer through the optical fiber. After the analog-to-digital conversion, the data is input into the computer for data analysis and processing. In the experiment, the integral time of the spectrometer was set 1 ms, and the flame radiation spectrum of the propellant combustion process was recorded continuously (time interval 100 ms).
Figure 3.Experiment system
The standard ϕ118 solid rocket motor used in the experiment isused primarily to study and evaluate the propellant formula and the burning rate of the propellant. Composite solid propellants are used in the experiment and the main formulations are ammonium perchlorate and aluminum. In order to study the influence of aluminum content of solid propellant on radiation spectrum, plume temperature and emissivity,the propellant with an aluminum mass fraction of 12%, 15% and 19% are selected for experimental study.
4 Experimental results and analysis
4.1 Typical exhaust plume flame radiation spectrum
In the experiment, a measuring system of exhaust plume flame radiation spectrum is built to measure the exhaust plume radiation spectrum of propellants with different aluminum content. The radiation spectrum of exhaust plume with 12% aluminum content at different time ranges of 350~1 000 nm is obtained. As shown in Fig.4, it can be seen that the exhaust plume radiation spectra at the different time have the characteristics of a continuous spectrum of solid radiation and dispersion of metal atomic characteristic spectrum. In solid rocket motors, the propellant combustion produces a high-temperature gas containing a large number of aluminum oxide condensate particles from the nozzle to produce thrust.These high-temperature condensate particles exhibit the continuous radiation spectral characteristics of solids in the band range. Besides, the propellant contains metal elements such as aluminum and sodium, which are ionized by heat to form gaseous free atoms and ions, and these free atoms and ions emit strong atomic characteristic lines. These discrete atomic characteristic lines are superimposed with the solid continuous radiation spectrum to form the plume flame radiation spectrum.
Figure 4.Typical plume radiation spectrums
As shown in Fig.4, according to the atomic spectra database of the National Institute of Standards and Technology (NIST)[
It can be seen from Fig.4 that after the ignition of the solid rocket motor, for the time from ① to ③, the solid propellant continues to burn, the plume temperature continues to rise, and the continuous radiation spectrum and the atomic characteristic spectrum are continuously enhanced. However, at time ④, the propellant gradually burns out, the combustion temperature and particle concentration decrease, and the plume continuous radiation spectrum and atomic characteristic spectrum are weakened. The spectral characteristics of plume radiation can reflect the internal combustion of the motor.The intensity of continuous radiation spectrum and atomic characteristic spectrum is closely related to combustion.
4.2 Plume flame ash hypothesis discussion
According to the above-mentioned principle of radiation spectral temperature measurement, the flame ash hypothesis is the basis of accurate temperature measurement. Therefore, this paper comprehensively considers factors including spectral signal-to-noise ratio, linear spectral response and spectral characteristics et al. Then the band range of 675~745 nm is selected as the range of radiation spectral parameters to fit the temperature data, and the change of exhaust plume flame emissivity with wavelength is mainly discussed.
Based on the gray judging principle of the two-color method[
Figure 5.Emissivity varies with wavelength
Table Infomation Is Not Enable4.3 Plume temperature and emissivity measurements
On the basis of the above assumption of exhaust plume flame ash body and Planck radiation law, a range of 675~745 nm band was selected. This range of band can perform parameter fitting on the plume radiation spectrum of 12% aluminum-containing solid rocket motor to get results of plume temperature and emissivity during motor working time. As shown in Fig.6, after the ignition of the motor, the overall trend of plume temperature and emissivity kept increasing. However, both of them had an inverse correlation to some extent in the adjacent in a short time. As the temperature decreased, the emissivity increases. In the band range of 675~745 nm, plume emissivity is related to such parameters as particle size, surface radiation characteristics, the concentration of condensate particles in the plume. Therefore, the inverse correlation between temperature and emissivity performance in the adjacent near the short time is related to the combustion of propellant aluminum particles. In a short time, the burning conditions are closed, when aluminum burning more fully, the combustion temperature is higher, product condensed phase particle size smaller that leads to reducing the emissivity.
Figure 6.Temperature and emissivity
In Fig.6, ① to ④are the typical moments of Fig.4. Corresponding to Fig.4, the measurement results of these four typical moments are shown in Table 2. Fig.4 shows the typical moment of the radiation spectrum. After the motor ignition, the plume radiation intensity increases, the temperature and emissivity overall show a rising trend. When nearly burnt out, although the plume temperature is slightly decreased (around 50 k), the aluminum combustion form of condensed phase particle concentration has fallen that reduced the radiation rate quickly is about 20%.
4.4 Radiation spectrum and temperature analysis of motor under different working conditions
The plume flame radiation spectrum of solid rocket motor with an aluminum content of 12%, 15% and 19% are measured. The average time treated radiation spectrum of the motor during the working period is taken. As shown in Fig.7, with the increase of aluminum content, the concentration of condensate particles in exhaust plume is higher, and the solid radiation is substantial. Therefore, the corresponding radiation spectral intensity increases significantly, and the amplitude of the radiation intensity increases with the increase of aluminum content. Taking 725.29 nm as an example, the spectral intensity of plume flame radiation of 19% aluminum-containing propellant is 9.6 times that of 15% aluminum-containing propellant. The spectral intensity of the plume flame radiation of the 15% aluminum-containing propellant is 2.0 times higher than that of the 12% aluminum-containing propellant.
Figure 7.Radiation spectrums of the plume of different propellants with aluminum mass contents of 12%, 15%, and 19%
The wavelength range of 675~745 nm is selected as the parameter fitting range. The radiation spectrum in Fig.7 is carried out the parameter fitting based on Planck’s radiation law to obtain the plume temperature and emissivity parameters. Meanwhile, the minimum free energy method of thermodynamic calculation method is carried out for the experimental solid rocket motor. Under the experiment condition, plume equilibrium flow temperature of propellant with different aluminum content is calculated, and the results are taken as reference. In Table 2, it can be seen that the maximum deviation between the measurement result and the thermal calculation result is 5.40%, which verifies the accuracy of the measurement of plume temperature of solid rocket motor by the radiation spectrum method.
In addition, the influence of propellant aluminum content on exhaust plume temperature and emissivity parameters can also be analyzed from Table 3. With the increase of the content of the propellant aluminum, the combustion temperature and emissivity both increased significantly. This is because, in the solid rocket propellant combustion, aluminum as the primary fuel component of the propellant combustion provides heat energy. The higher the aluminum content, the greater the power contained in the propellant, and the higher the temperature of the plume produced by combustion. The radiation in the band range of 675~745 nm is mainly reflected in the solid radiation of condensate particles generated by the combustion of aluminum particles, and its emissivity is related mostly to the concentration of condensate particles and the surface radiation characteristics. For the exhaust plume, most of the aluminum is completely burned, and the condensate particles are mainly aluminum oxide, and the surface radiation characteristics of the condensate particles are similar. Therefore, the plume radiation of the motor is determined primarily by the concentration of the condensate particles.
5 Conclusion
In this paper, the plume radiation spectral temperature measurement method of a solid rocket motor is mainly studied; the following findings are obtained:
(1) A method for measuring plume temperature of solid rocket motor based on flame radiation spectrum is proposed. Calibration of the response coefficient of the spectrometer is carried out with standard radiation blackbody furnace, and the curve of response coefficient with wavelength is obtained, which is used as plume radiation spectral data correction. The method is applied to the ground test of standard 118 solid rocket motor to carry out spectral measurement of plume radiation of solid rocket motor with different propellant formulations with 12%, 15% and 19% aluminum mass contents, and obtain plume temperature and emissivity parameters. The maximum deviation between the temperature measurement and the theoretical thermodynamic calculation is 5.40%.
(2) The graybody characteristics of solid rocket exhaust plume flame in the band range of 675~745 nm are discussed by using the gray property judgment principle of the two-color method. The changes in flame emissivity with wavelength are obtained. The maximum relative deviation of emissivity with wavelength is 4.01%, and the corresponding mean-variance is 1.53%, both of which are less than 5%. It can be considered that the plume of solid rocket motor with a large number of solid particles is a gray body in the band range of 675~745 nm, which lays a foundation for temperature measurement by using the radiation spectral parameter fitting method.
(3) The spectral analysis of solid rocket motor plume radiation in the band range of 350~1 000 nm has the characteristics of the continuous spectrum of solid radiation and dispersion of metal atomic characteristic spectral lines. By combining the measurement results of temperature and emissivity, the spectral characteristics of plume radiation of solid rocket motor with different aluminum content are discussed, and the effects of aluminum content of solid propellant on the radiation spectrum, plume temperature and emissivity are analyzed. It provides important experimental data support for reducing the characteristic plume signal of the solid motor.
References
[1] Y Li, S Zhu, W Zhao et al. Journal of Thermophysics and Heat Transfer, 18, 404(2004).
[2] C Dennis, B Bojko. Fuel, 254, 115646(2019).
[3] F Boyarshinov B, Y Fedorov S. Journal of Applied Mechanics and Technical Physics, 43, 925(2002).
[4] R Yang, Y Li, J Zhang et al. Combustion and Flame, 145, 836(2006).
[5] J Liu, M Duan, T Fu et al. Review of Scientific Instruments, 85, 044901(2014).
[6] B Sun, X Sun, M Liang et al. Measurement, 95, 239(2017).
[7] Changhui Wang, Lei Liang, Mei Liang et al. Spectroscopy and Spectral Analysis, 38, 2860(2018).
[8] C Lou, W Yan, H Zhou et al. Energy & Fuels, 27, 6754(2013).
[9] K Li, W Yan, X Huang et al. Energy & Fuels, 34, 907(2020).
[10] Haoran Guo, Xinyang Gui, Bin Yang et al. Spectroscopy and Spectral Analysis, 38, 1958(2018).
[11] F Modest M. Radiative Heat Transfer. Academic Press(2003).
[12] . NIST Atomic Spectra Database. http://www.nist.gov/pml/data/asd.cfm
[13] Chun Lou, Haichun Zhou, Yipeng Sun. Proceedings of the Combustion Institute, 33, 735(2011).
Set citation alerts for the article
Please enter your email address