[1] Blackley W S and Scattergood R O 1994 Chip topography for ductile-regime machining of germanium J. Manuf. Sci. Eng. 116 263–6
[2] Shibata T, Fujii S, Makino E and Ikeda M 1996 Ductile-regime turning mechanism of single-crystal silicon Prec. Eng. 18 129–37
[3] Randall T, Walter J J H, Scattergood R and Nemanich R 2009 High pressure phase transformation and ductility in diamond turned single crystal silicon North Carolina State University Raleigh NC27695Y7918
[4] Goel S, Kovalchenko A, Stukowski A and Cross G 2016 Influence of microstructure on the cutting behaviour of silicon Acta Mater. 105 464–78
[5] Goel S, Luo X C, Reuben R L and Pen H M 2012 Influence of temperature and crystal orientation on tool wear during single point diamond turning of silicon Wear 284-5 65–72
[6] Yan J W, Syoji K, Kuriyagawa T and Suzuki H 2002 Ductile regime turning at large tool feed J. Mater. Process. Technol. 121 363–72
[7] Chavoshi S Z, Goel S and Morantz P 2017 Current trends and future of sequential micro-machining processes on a single machine tool Mater. Des. 127 37–53
[8] Rashid W B and Goel S 2016 Advances in the surface defect machining (SDM) of hard steels J. Manuf. Process. 23 37–46
[9] Rashid W B, Goel S, Luo X C and Ritchie J M 2013 The development of a surface defect machining method for hard turning processes Wear 302 1124–35
[10] Rashid W B, Goel S, Luo X C and Ritchie J M 2013 An experimental investigation for the improvement of attainable surface roughness during hard turning process Proc. Inst. Mech. Eng. B 227 338–42
[11] Goel S, Rashid W B, Luo X C, Agrawal A and Jain V K 2014 A theoretical assessment of surface defect machining and hot machining of nanocrystalline silicon carbide J. Manuf. Sci. Eng. 136 021015
[12] Komanduri R, Lee M, Flom D G, Thompson R A, Jones M G and Douglas R J 1982 Pulse laser pretreated machining. US Patent 4356376
[13] Mir A, Luo X C and Siddiq A 2017 Smooth particle hydrodynamics study of surface defect machining for diamond turning of silicon Int. J. Adv. Manuf. Technol. 88 2461–76
[14] Mylvaganam K, Zhang L C, Eyben P, Mody J and Vandervorst W 2019 Evolution of metastable phases in silicon during nanoindentation: mechanism analysis and experimental verification Nanotechnology 20 305705
[15] Smith G S, Tadmor E B and Kaxiras E 2000 Multiscale simulation of loading and electrical resistance in silicon nanoindentation Phys. Rev. Lett. 84 1260–3
[16] Smith G S, Tadmor E B, Bernstein N and Kaxiras E 2001 Multiscale simulations of silicon nanoindentation Acta Mater. 49 4089–101
[17] Goel S, Luo X C, Agrawal A and Reuben R L 2015 Diamond machining of silicon: a review of advances in molecular dynamics simulation Int. J. Mach. Tools Manuf. 88 131–64
[18] Goel S, Llavori I, Zabala A, Giusca C, Veldhuis S C and Endrino J L 2018 The possibility of performing FEA analysis of a contact loading process fed by the MD simulation data Int. J. Mach. Tools Manuf. 134 79–80
[19] Mariayyah R 2007 Experimental and numerical studies of ductile regime machining of silicon carbide and silicon nitride PhD Thesis (Charlotte, NC: The University of North Carolina at Charlotte)
[20] Venkatachalam S 2007 Predictive modeling for ductile machining of brittle materials PhD Thesis (Atlanta, GA: Georgia Institute of Technology)
[21] Jasinevicius R G, Duduch J G, Montanari L and Pizani P S 2008 Phase transformation and residual stress probed by Raman spectroscopy in diamond-turned single crystal silicon Proc. Inst. Mech. Eng. B 222 1065–73
