Research Progress on Rheological Properties of Light-Cured Alumina Ceramic Slurry

MIAO Xinyu; LU Ping; LIU Shuangyu; LI Yinhao; ZHANG Fulong; LI Liang; ZHANG Haoli

[2] SANTOLIQUIDO O, COLOMBO P, ORTONA A. Additive manufacturing of ceramic components by Digital Light Processing: a comparison between the “bottom-up” and the “top-down” approaches［J］. Journal of the European Ceramic Society, 2019, 39(6): 2140-2148.

[3] LIAN Q, YANG F, XIN H, et al. Oxygen-controlled bottom-up mask-projection stereolithography for ceramic 3D printing［J］. Ceramics International, 2017, 43(17): 14956-14961.

[4] Technology-Additive Manufacturing Technology; Researchers from Swiss Federal Laboratories for Materials Science and Technology Report on Findings in Additive Manufacturing Technology (Fabrication of ZrO2 and Atz Materials Via Uv-lcm-dlp Additive Manufacturing Technology)［J］. Journal of Engineering, 2020.

[7] KOMISSARENKO D A, SOKOLOV P S, EVSTIGNEEVA A D, et al. Rheological and curing behavior of acrylate-based suspensions for the DLP 3D printing of complex zirconia parts［J］. Materials (Basel, Switzerland), 2018, 11(12): 2350.

[9] ZENG Q F, YANG C H, TANG D Y, et al. Additive manufacturing alumina components with lattice structures by digital light processing technique［J］. Journal of Materials Science & Technology, 2019, 35(12): 2751-2755.

[10] XING Z W, LIU W W, CHEN Y, et al. Effect of plasticizer on the fabrication and properties of alumina ceramic by stereolithography-based additive manufacturing［J］. Ceramics International, 2018, 44(16): 19939-19944.

[11] GONZALEZ P, SCHWARZER E, SCHEITHAUER U, et al. Additive manufacturing of functionally graded ceramic materials by stereolithography［J］. Journal of Visualized Experiments (JoVE), 2019(143): e57943.

[12] GRIFFITH M L, HALLORAN J W. Freeform fabrication of ceramics via stereolithography［J］. Journal of the American Ceramic Society, 1996, 79(10): 2601-2608.

[13] JANG K J, KANG J H, FISHER J G, et al. Effect of the volume fraction of zirconia suspensions on the microstructure and physical properties of products produced by additive manufacturing［J］. Dental Materials, 2019, 35(5): e97-e106.

[14] YUN J S, PARK T W, JEONG Y H, et al. Development of ceramic-reinforced photopolymers for SLA 3D printing technology［J］. Applied Physics A, 2016, 122(6): 629.

[15] ZHANG S, SHA N, ZHAO Z. Surface modification of α-Al2O3 with dicarboxylic acids for the preparation of UV-curable ceramic suspensions［J］. Journal of the European Ceramic Society, 2017, 37(4): 1607-1616.

[16] HINCZEWSKI C, CORBEL S, CHARTIER T. Stereolithography for the fabrication of ceramic three- dimensional parts［J］. Rapid Prototyping Journal, 1998, 4(3): 104-111.

[17] ZHANG K Q, HE R J, XIE C, et al. Photosensitive ZrO2 suspensions for stereolithography［J］. Ceramics International, 2019, 45(9): 12189-12195.

[18] LIU D M. Particle packing and rheological property of highly-concentrated ceramic suspensions: φm determination and viscosity prediction［J］. Journal of Materials Science, 2000, 35(21): 5503-5507.

[19] KRIEGER I M, DOUGHERTY T J. A mechanism for non-Newtonian flow in suspensions of rigid spheres［J］. Transactions of the Society of Rheology, 1959, 3(1): 137-152.

[20] ZHANG K Q, XIE C, WANG G, et al. High solid loading, low viscosity photosensitive Al2O3 slurry for stereolithography based additive manufacturing［J］. Ceramics International, 2019, 45(1): 203-208.

[21] ZHANG S, SHA N, ZHAO Z. Surface modification of α-Al2O3 with dicarboxylic acids for the preparation of UV-curable ceramic suspensions［J］. Journal of the European Ceramic Society, 2017, 37(4): 1607-1616.

[22] DUFAUD O, MARCHAL P, CORBEL S. Rheological properties of PZT suspensions for stereolithography［J］. Journal of the European Ceramic Society, 2002, 22(13): 2081-2092.

[23] BORLAF M, SERRA-CAPDEVILA A, COLOMINAS C, et al. Development of UV-curable ZrO2 slurries for additive manufacturing (LCM-DLP) technology［J］. Journal of the European Ceramic Society, 2019, 39(13): 3797-3803.

[24] DE CAMARGO I L, MORAIS M M, FORTULAN C A, et al. A review on the rheological behavior and formulations of ceramic suspensions for vat photopolymerization［J］. Ceramics International, 2021, 47(9): 11906-11921.

[25] LI K H, ZHAO Z. The effect of the surfactants on the formulation of UV-curable SLA alumina suspension［J］. Ceramics International, 2017, 43(6): 4761-4767.

[26] JOHANSSON E, LIDSTRM O, JOHANSSON J, et al. Influence of resin composition on the defect formation in alumina manufactured by stereolithography［J］. Materials (Basel, Switzerland), 2017, 10(2): 138.

[27] ADAKE C V, BHARGAVA P, GANDHI P. Effect of surfactant on dispersion of alumina in photopolymerizable monomers and their UV curing behavior for microstereolithography［J］. Ceramics International, 2015, 41(4): 5301-5308.

[28] WOZNIAK M, DE HAZAN Y, GRAULE T, et al. Rheology of UV curable colloidal silica dispersions for rapid prototyping applications［J］. Journal of the European Ceramic Society, 2011, 31(13): 2221-2229.

[29] KOTZ F, ARNOLD K, BAUER W, et al. Three-dimensional printing of transparent fused silica glass［J］. Nature, 2017, 544(7650): 337-339.

[30] WANG Z, HUANG C Z, WANG J, et al. Development of a novel aqueous hydroxyapatite suspension for stereolithography applied to bone tissue engineering［J］. Ceramics International, 2019, 45(3): 3902-3909.

[31] ZHOU M P, LIU W, WU H D, et al. Preparation of a defect-free alumina cutting tool via additive manufacturing based on stereolithography-Optimization of the drying and debinding processes［J］. Ceramics International, 2016, 42(10): 11598-11602.

[32] VAN DEN BRAND J, BLAJIEV O, BEENTJES P C J, et al. Interaction of ester functional groups with aluminum oxide surfaces studied using infrared reflection absorption spectroscopy［J］. Langmuir: the ACS Journal of Surfaces and Colloids, 2004, 20(15): 6318-6326.

[33] LI H, LIU Y S, LIU Y S, et al. Microstructure and properties of 3D-printed alumina ceramics with different heating rates in vacuum debinding［J］. Rare Metals, 2020, 39(5): 577-588.

[34] WANG Y Y, WANG Z Y, LIU S H, et al. Additive manufacturing of silica ceramics from aqueous acrylamide based suspension［J］. Ceramics International, 2019, 45(17): 21328-21332.

[35] LI H, LIU Y S, LIU Y S, et al. 3D printed ceramic slurries with improved solid content through optimization of alumina powder and coupling agent［J］. Journal of Manufacturing Processes, 2021, 64: 1206-1213.

[36] LANGMUIR I. The constitution and fundamental properties of solids and liquids. part i. solids［J］. Journal of the American Chemical Society, 1916, 38(11): 2221-2295.

[37] DIPTANSH U, MIAO G X, MA C. Vat photopolymerization 3D printing of ceramics: effects of fine powder［J］. Manufacturing Letters, 2019, 21: 20-23.

[38] ZHANG K Q, HE R J, DING G J, et al. Effects of fine grains and sintering additives on stereolithography additive manufactured Al2O3 ceramic［J］. Ceramics International, 2021, 47(2): 2303-2310.

[41] XING H Y, ZOU B, LAI Q G, et al. Preparation and characterization of UV curable Al2O3 suspensions applying for stereolithography 3D printing ceramic microcomponent［J］. Powder Technology, 2018, 338: 153-161.

[42] GOSWAMI A, K A, BALASHANMUGAM N, et al. Optimization of rheological properties of photopolymerizable alumina suspensions for ceramic microstereolithography［J］. Ceramics International, 2014, 40(2): 3655-3665.

[43] YU Y, ZOU B, WANG X, et al. Rheological behavior and curing deformation of paste containing 85 wt% Al2O3 ceramic during SLA-3D printing［J］. Ceramics International, 2022, 48(17): 24560-24570.