Researching | Side-Surface-Form Analysis of Arc Additive Manufacturing Based on Laser Vision Sensing System

Journals >Chinese Journal of Lasers >Volume 46 >Issue 11 >Page 1102005 > Article

Chinese Journal of Lasers
Vol. 46, Issue 11, 1102005 (2019)

Side-Surface-Form Analysis of Arc Additive Manufacturing Based on Laser Vision Sensing System

Bo Ma, Xiangdong Gao^*, Yijie Huang, Yanxi Zhang, Deyong You, and Nanfeng Zhang

Author Affiliations

Guangdong Provincial Welding Engineering Technology Research Center, Guangdong University of Technology,Guangzhou, Guangdong 510006, China

show less

DOI: 10.3788/CJL201946.1102005 Cite this Article Set citation alerts

Bo Ma, Xiangdong Gao, Yijie Huang, Yanxi Zhang, Deyong You, Nanfeng Zhang. Side-Surface-Form Analysis of Arc Additive Manufacturing Based on Laser Vision Sensing System[J]. Chinese Journal of Lasers, 2019, 46(11): 1102005 Copy Citation Text

show less

References

[1] Zhou X M, Tian Q H, Du Y X et al. Simulation of grain growth in single-pass two-layer deposition of arc welding based additive forming process[J]. Journal of Mechanical Engineering, 54, 86-94(2018).

[2] Feng Y, Zhang P X, Jia J L. Research progress of wire + arc additive manufacturing in past two years[J]. Hot Working Technology, 47, 23-26(2018).

[3] Xiong J, Xue Y G, Chen H et al. Status and development prospects of forming control technology in arc-based additive manufacturing[J]. Electric Welding Machine, 45, 45-50(2015).

[4] Yang H O, Wang J, Zhou Y H et al. Wire and arc additive manufacturing technology and its application in TC4 titanium alloy: a review[J]. Materials Review, 32, 1884-1890(2018).

[5] Shi J B, Li F, Chen S J et al. Effect of in-process active cooling on forming quality and efficiency of tandem GMAW-based additive manufacturing[J]. The International Journal of Advanced Manufacturing Technology, 101, 1349-1356(2019). http://link.springer.com/article/10.1007%2Fs00170-018-2927-4

[6] Xiong J, Li Y J, Li R et al. Influences of process parameters on surface roughness of multi-layer single-pass thin-walled parts in GMAW-based additive manufacturing[J]. Journal of Materials Processing Technology, 252, 128-136(2018). http://www.sciencedirect.com/science/article/pii/S0924013617304193

[7] Li Y Z, Huang X, Horváth I et al. GMAW-based additive manufacturing of inclined multi-layer multi-bead parts with flat-position deposition[J]. Journal of Materials Processing Technology, 262, 359-371(2018). http://www.onacademic.com/detail/journal_1000040429903410_725c.html

[8] Gao X D, Long G F, Wang R L et al. Analysis of characteristics of spatters during high-power disk laser welding[J]. Acta Physica Sinica, 61, 098103(2012).

[9] Ding Y Y, Zhang X B, Kovacevic R. A laser-based machine vision measurement system for laser forming[J]. Measurement, 82, 345-354(2016). http://www.sciencedirect.com/science/article/pii/S026322411600018X

[10] Huang Y J, Gao X D, Lin S D. Influences of laser welding parameters on mechanical properties of polymethyl methacrylate and stainless-steel joints[J]. Chinese Journal of Lasers, 44, 1202006(2017).

[11] Zhang B, Chang S, Wang J et al. Feature points extraction of laser vision weld seam based on genetic algorithm[J]. Chinese Journal of Lasers, 46, 0102001(2019).

[12] Zhang P X, Zhang G Q, Wei Z C et al. Laser vision measurement for 3D surface outline of groove and weld[J]. Transactions of the China Welding Institution, 38, 85-89(2017).

[13] Rodríguez-Martín M, Rodríguez-Gonzálvez P, González-Aguilera D et al. Feasibility study of a structured light system applied to welding inspection based on articulated coordinate measure machine data[J]. IEEE Sensors Journal, 17, 4217-4224(2017). http://ieeexplore.ieee.org/document/7921608/

[14] Wang W C, Gao X D, Ding X D et al. Detection of non-groove butt joint feature based on corner principle[J]. Transactions of the China Welding Institution, 39, 61-64(2018).

[15] Cloud Compare[2019-05-01]. 3D point cloud and mesh processing software open source project [2019-05-01].http:∥www.danielgm.net/..

[16] Huang K, Cheng X J, Jia D F et al. An automatic segmentation algorithm for dense pipeline point cloud data[J]. Chinese Journal of Lasers, 45, 1104004(2018).

Get PDF(in Chinese)

Figures&Tables (15)

References (16)

Copy Citation Text

Bo Ma, Xiangdong Gao, Yijie Huang, Yanxi Zhang, Deyong You, Nanfeng Zhang. Side-Surface-Form Analysis of Arc Additive Manufacturing Based on Laser Vision Sensing System[J]. Chinese Journal of Lasers, 2019, 46(11): 1102005

Download Citation

Set citation alerts for the article

Set citation alerts for the article

Save the article for my favorites

Paper Information

Recommended Topics

laser devices and laser physics

Lasers and Laser Optics

laser manufacturing

Instrumentation, Measurement and Metrology

Set citation alerts for the article

Please enter your email address