[1] LIU D W,ZHANG Z G,ZHANG X Y,et al. 3D printing concrete structures: state of the art,challenges,and opportunities［J］. Construction and Building Materials,2023,405: 133364.
[2] GENG Z F,SHE W,ZUO W Q,et al. Layer-interface properties in 3D printed concrete: dual hierarchical structure and micromechanical characterization［J］. Cement and Concrete Research,2020,138: 106220.
[3] NERELLA V N,HEMPEL S,MECHTCHERINE V. Effects of layer-interface properties on mechanical performance of concrete elements produced by extrusion-based 3D-printing［J］. Construction and Building Materials,2019,205: 586-601.
[4] YU S W,XIA M,SANJAYAN J,et al. Microstructural characterization of 3D printed concrete［J］. Journal of Building Engineering,2021,44: 102948.
[5] RAHUL A V,SANTHANAM M,MEENA H,et al. Mechanical characterization of 3D printable concrete［J］. Construction and Building Materials,2019,227: 116710.
[6] ZHANG J,ZOU D Q,WANG H L,et al. Bond tensile performance and constitutive models of interfaces between vertical and horizontal filaments of 3D printed concrete［J］. Journal of Zhejiang University (Engineering Science),2021,55(11): 2178-2185+2214 (in Chinese).
[7] NAPOLITANO R,MENNA C,FORNI D,et al. Dynamic behaviour of layered 3D printed concrete elements［C］//RILEM International Conference on Concrete and Digital Fabrication. Cham: Springer,2020: 478-488.
[8] SANJAYAN J G,NEMATOLLAHI B,XIA M,et al. Effect of surface moisture on inter-layer strength of 3D printed concrete［J］. Construction and Building Materials,2018,172: 468-475.
[9] LIU Z Y,WANG Z D,WANG L,et al. Interlayer bond strength of 3D printing cement paste by cross-bonded method［J］. Journal of the Chinese Ceramic Society,2019,47(5): 648-652 (in Chinese).
[10] MOELICH G M,KRUGER J,COMBRINCK R. Modelling the interlayer bond strength of 3D printed concrete with surface moisture［J］. Cement and Concrete Research,2021,150: 106559.
[11] YAO H,XIE Z L,LI Z M,et al. The relationship between the rheological behavior and interlayer bonding properties of 3D printing cementitious materials with the addition of attapulgite［J］. Construction and Building Materials,2022,316: 125809.
[12] VAN DEN HEEVER M,BESTER F,KRUGER J,et al. Numerical modelling strategies for reinforced 3D concrete printed elements［J］. Additive Manufacturing,2022,50: 102569.
[13] PAN Z F,SI D D,TAO J H,et al. Compressive behavior of 3D printed concrete with different printing paths and concrete ages［J］. Case Studies in Construction Materials,2023,18: e01949.
[14] YANG Y K,WU C Q,LIU Z X. Rate dependent behaviour of 3D printed ultra-high performance fibre-reinforced concrete under dynamic splitting tensile［J］. Composite Structures,2023,309: 116727.
[15] VALLE-PELLO P,LVAREZ-RABANAL F P,ALONSO-MARTNEZ M,et al. Numerical study of the interfaces of 3D-printed concrete using discrete element method［J］. Materials Science & Engineering Technology,2019,50: 629-634.
[16] WANG L,JIANG H L,LI Z J,et al. Mechanical behaviors of 3D printed lightweight concrete structure with hollow section［J］. Archives of Civil and Mechanical Engineering,2020,20(1): 16.
[17] DEN-HEEVER M V,ANTON D P,FREDERICK B,et al. A mechanistic evaluation relating microstructural morphology to a modified Mohr-Griffith compression-shear constitutive model for 3D printed concrete［J］. Construction and Building Materials,2022,325: 126743.
[18] VAN DEN HEEVER M,BESTER F,POURBEH M,et al. Characterizing the fissility of 3D concrete printed elements via the cohesive zone method［C］. Second RILEM International Conference on Concrete and Digital Fabrication. Springer,Cham,2020: 489-499.
[19] XIAO J Z,LIU H R,DING T. Finite element analysis on the anisotropic behavior of 3D printed concrete under compression and flexure［J］. Additive Manufacturing,2021,39: 101712.
[20] Ministry of Housing and Urban-Rural Development of the Peoples Republic of China,State Administration for Market Supervision and Administration. Standards for test methods of physical and mechanical properties of concrete: GB/T 50081—2019［S］. Beijing: China Construction Industry Publishing House,2019 (in Chinese).
[21] Standardization Administration of China. Test method for interfacial bond strength of fine ceramic materials: cross-bonded: GB/T 31541—2015［S］. Beijing: Standard Press of China,2016 (in Chinese).
[22] LUBLINER J,OLIVER J,OLLER S,et al. A plastic-damage model for concrete［J］. International Journal of Solids and Structures,1989,25(3): 299-326.
[23] HILLERBORG A,MODER M,PETERSSON P E. Analysis of crack formation and crack growth in concrete by means of fracture mechanics and finite elements［J］. Cement and Concrete Research,1976,6: 773-781.
[24] WANG H L,SHAO J W,ZHANG J,et al. Bond shear performances and constitutive model of interfaces between vertical and horizontal filaments of 3D printed concrete［J］. Construction and Building Materials,2022,316: 125819.
