Abstract
1. Introduction
Nowadays, the multimode fiber (MMF), which was overlooked for decades, is making a strong comeback since it can address plenty of long-standing issues relating to the single-mode fiber (SMF). For optical communication, based on the spatial division multiplexing technique[
As for the application of the MMF in high power lasers, it was mainly limited to the continuous wave (CW) laser in the past[
In the QML operation state, the pulse-train is a continuous pulse-train modulated periodically by a -switched envelope. It can be seen as the transition state between the -switched state and the continuous mode-locked state. Therefore, QML pulses have characteristics of both -switched pulses and continuous mode-locked pulses. Compared to continuous mode-locked fiber lasers[
Sign up for Chinese Optics Letters TOC. Get the latest issue of Chinese Optics Letters delivered right to you!Sign up now
In this work, we address this issue. By constructing an Yb-doped MMF laser with a graphene-deposited multimode microfiber (GMM), the QML pulses are obtained. The single-wavelength QML operation in the MMF laser is firstly realized, and the central wavelength can be tuned from 1028.81 nm to 1039.20 nm. Particularly, we observe the generation of the fifth harmonic in the QML operation. In addition, the MMF laser can operate at the dual-wavelength QML state due to the filtering effect induced by the few-mode fiber and MMF structure and the GMM in the cavity. Furthermore, the dual-wavelength spacing can be tuned from 0.93 nm to 5.79 nm. The obtained results demonstrate that the QML pulses can be obtained in the MMF laser, and such a flexible laser with tunable wavelength would be helpful in applications of optical sensing, measuring, and laser processing.
2. Experimental Setup
The schematic of the proposed MMF laser is shown in Fig. 1. The gain fiber is a piece of long double-cladding Yb-doped fiber (YDF, Liekki Yb1200-10/125 DC, core , cladding ) and pumped by a 980 nm laser diode through a customized combiner with 10/125 µm fiber pigtails with the core NA of 0.08 and the cladding NA of 0.46. The YDF supports three transvers modes. The GMM is incorporated into the cavity to realize the QML operation. A polarization-independent isolator (PI-ISO) is used to ensure the unidirectional light propagation in the laser cavity. Two polarization controllers (PCs) are employed to optimize the operation state of the laser by adjusting the polarization state of the light. The laser is taken out for measuring by an optical coupler (OC) with an output ratio of 10%. Except for the YDF and the fiber pigtails of the combiner being few-mode fibers, all other fibers including the pigtails of the PI-ISO and the 90:10 OC in the cavity are conventional graded-index MMFs (Corning, 62.5/125 µm, ). The splice between the MMF and the few-mode fiber is completed by an arc fusion splicer. Due to the mismatch of the NAs, the splice loss for the light propagating from the passive few-mode fiber to the MMF is different from that of light propagating from the MMF to the passive few-mode fiber, which is and , respectively. The total length of the cavity is 16.9 m. We fasten all of the fibers on the optical table to maintain stable laser operation. The laser optical spectrum and frequency spectrum are measured by an optical spectrum analyzer (OSA, Yokogawa, AQ6317C) and a radio-frequency (RF) spectrum analyzer (Agilent, E4407B ESA-E SERIES, 26.5 GHz), respectively. An oscilloscope (Tektronix, DSA70804, 8 GHz) together with a photodetector (Newport, 1623 InGaAs nanosecond optical detector, 500 MHz) is used to measure the pulse-train. Moreover, a charge-coupled device (CCD) camera (Goldeye G-033SWIRTEC1) is used to measure the beam profile.
Figure 1.Experimental setup of the QML MMF laser with a GMM.
As the key component for achieving the QML operation, the GMM incorporated in the cavity is firstly fabricated through the following steps. Firstly, the multimode microfiber with a waist diameter of 6.73 µm, a waist length of 2.3 cm, and a loss of is made from the conventional graded-index MMF (Corning, 62.5/125 µm, ) by the flame brushing technique. Then, the multimode microfiber is transferred to a glass slide for depositing the graphene. For the purpose of uniformity, the graphene/dimethylformamide (DMF) solution with a concentration of 0.05 mg/mL, which will be dropped onto the multimode microfiber during the process of the deposition, is ultrasonicated for 30 min. After that, the optical deposition method described in Ref. [37] is employed. The process of the deposition is in situ observed through a microscope. The amount of the graphene deposited on the multimode microfiber can be controlled by adjusting the light power and the deposition time. In addition, the loss induced by the deposition is monitored by a power meter. The GMM with a deposition length of used in our experiment is shown in Fig. 2(a).
Figure 2.(a) Microscope image of the fabricated GMM; (b) nonlinear saturable absorption curve and the corresponding fitting curve of the fabricated GMM; (c) spectral filtering characteristic of the fabricated GMM.
To further investigate the features of the fabricated GMM, we measure its nonlinear absorption by a balanced twin detector measurement technology. The light source used in the measurement is an in-house made picosecond pulse MMF laser (central wavelength, 1070 nm; repetition rate, 13.60 MHz). To control the input power of the GMM, a variable attenuator is used. The nonlinear transmission curve and the fitting curve of the GMM are illustrated in Fig. 2(b). As can be seen from Fig. 2(b), the fabricated GMM has the saturable absorption effect. The modulation depth is , and the non-saturable loss is . The modulation depth could be increased, and the non-saturable loss could be decreased by optimizing the deposition amount of the graphene. Such a large modulation depth and a large non-saturable loss are conducive to the generation of QML pulses. In addition to the saturable absorption effect, the GMM also has a filtering effect, as illustrated in Fig. 2(c), which is mainly formed by multimode interference in the taper’s waist region[
3. Experimental Results and Discussions
3.1 Single-wavelength QML operation
In our experiment, the CW operation is firstly achieved at the pump power of . Then, by slightly increasing the pump power to , the QML operation is realized. Figure 3 presents the characteristics of the typical QML operation at the pump power of 1.40 W. Figure 3(a) displays the QML pulse-train with the repetition rate of 16.04 kHz. In order to demonstrate more details of the QML pulses, it is enlarged and shown in Figs. 3(b) and 3(c). The envelope width of the QML pulses is 8.14 µs. The corresponding mode-locked pulses underneath the -switched envelope have the repetition rate of 11.58 MHz, corresponding to the light round-trip time in the cavity. The optical spectrum is presented in Fig. 3(d), where the central wavelength locates at 1039.20 nm. Figure 3(e) displays the RF spectrum, which has multiple peaks with an interval of 16.04 kHz, in accordance with the repetition rate of the -switched pulse envelope. The corresponding beam profile shown in Fig. 3(f) exhibits a speckle spatial pattern, similar to those in STML MMF lasers[
Figure 3.QML operation at the pump power of 1.40 W. (a)–(c) QML pulse-train in the time range of 200 µs (20 µs/div), 20 µs (2 µs/div), and 200 ns (20 ns/div), respectively; (d) the corresponding optical spectrum; (e) the RF spectrum; (f) the beam profile.
Moreover, due to the filtering effect induced by the few-mode fiber (the gain fiber and the matched passive fiber of the combiner) and the MMF structure[
Figure 4.Wavelength-tunable QML operation at the pump power of 1.40 W.
Then, to further explore the characteristics of the QML operation, we investigate the evolution of the QML pulses at the central wavelength of 1034.80 nm by fixing the PCs and only adjusting the pump power. With the pump power increasing, it is found that the time interval between the adjacent -switched envelopes becomes shorter, as illustrated in Fig. 5(a). Figure 5(b) shows the repetition rate and the -switched pulse envelope width as a function of the pump power. The repetition rate increases monotonously from 18.19 kHz to 27.67 kHz, and the pulse envelope width decreases monotonously from 9.55 µs to 3.43 µs when the pump power increases from 1.30 W to 1.60 W, which are the typical characteristics of the QML operation. It can be interpreted that the time required to accumulate and release enough energy becomes shorter when the pump power increases. The pulse envelope width may be further shortened by reducing the length of the laser cavity[
Figure 5.Pump-dependent characteristics of the single-wavelength QML operation. (a) QML pulse-train under different pump power; (b) the pulse envelope width and repetition rate versus the pump power; (c) the average output power and pulse energy versus the pump power.
Particularly, we also observe harmonics in the -switched envelope. Figure 6 shows the characteristics of the QML operation with the fifth harmonic at the central wavelength of 1028.81 nm. Figure 6(a) shows the single QML pulse envelope, and the inset is the QML pulse-train on a larger time scale. The repetition rate and the pulse width of the -switched envelope are 23.87 kHz and 6.72 µs, respectively. The corresponding mode-locked pulses underneath the -switched envelope are illustrated in Fig. 6(b). The repetition rate of the mode-locked pulses is 57.97 MHz, corresponding to the fifth harmonic of the fundamental repetition rate of the cavity. It was demonstrated that harmonic mode-locked operation could be achieved by introducing appropriate highly nonlinear effects into the SMF laser cavity[
Figure 6.Single-wavelength fifth harmonic QML operation at the pump power of 1.40 W. (a) The Q-switched envelope in the time range of 20 µs (2 µs/div), while the inset is the pulse-train in the time range of 200 µs (20 µs/div); (b) the mode-locked pulse-train underneath the Q-switched envelope in the time range of 200 ns (20 ns/div); (c) the RF spectrum; (d) the beam profile.
3.2 Dual-wavelength QML operation
It is noted that in our MMF laser cavity, except for the GMM having a filtering effect, there is a few-mode fiber and MMF structure, which can form a filter and lead to the multiwavelength filtering effect[
Figure 7.Characteristics of the dual-wavelength QML operation. (a) The dual-wavelength spectra with different wavelength spacings at the pump power of 1.40 W; (b) the QML pulse-trains under different pump powers at the central wavelengths of 1030.48 nm and 1033.78 nm.
Furthermore, we investigate the evolution of the pulse envelope with the pump power at the dual-wavelength QML states. With the increase of the pump power, the width of the -switched pulse envelope narrows, and the repetition rate increases, which are the same as that of the single-wavelength state. Figure 7(b) shows the evolution of the dual-wavelength QML pulses at the central wavelengths of 1030.48 nm and 1033.78 nm with the pump power. As seen from Fig. 7(b), the time interval between the adjacent -switched envelopes becomes shorter when the pump power is increased. The repetition rate can be tuned from 14.16 kHz to 27.86 kHz when the pump power rises from 1.35 W to 1.60 W. Meanwhile, the pulse envelope width decreases monotonously. The minimum pulse envelope width is 3.38 µs at the pump power of 1.60 W.
In this QML MMF laser, single-wavelength-tunable and dual-wavelength spacing-tunable operations can be realized. It increases the flexibility of the laser applications. Note that the tunable range of the single wavelength is only 10.39 nm, and the maximum spacing-tunable range of the dual wavelength is only 5.79 nm. This is mainly limited by the characteristics of the filter based on the few-mode fiber and MMF structure and the GMM filter. It could achieve a larger wavelength/wavelength-spacing-tunable range by optimizing the parameters of the filters, such as the length of the MMF[
In our experiments, QML operation can be achieved by using different GMMs with waist diameters from 4.16 µm to 14.04 µm and modulation depths from 21.82% to 37.90%. However, the STML operation is unable to be achieved in our laser with these GMMs. Generally, the non-saturable loss of the saturable absorber increases as its modulation depth increases, and the relatively large loss is conducive to realizing the QML operation. Thus, we think that the main reason is that the modulation depths of the GMMs used in our laser are too large, which is accompanied with a relatively large non-saturable loss. In addition to the large modulation depth/non-saturable loss of the GMMs, another reason is that the splice losses of the cavity are too large since the different types of fibers are used in our laser. Thus, to achieve the STML operation in the future work, it is necessary to optimize the parameters of the fabricated GMM, such as the modulation depth and the non-saturable loss, and further reduce the loss of the cavity.
4. Conclusion
In conclusion, we report the QML pulses generation in an Yb-doped MMF fiber laser by using a GMM. Due to the filtering effect induced by the few-mode fiber and MMF structure and the GMM in the cavity, both the single-wavelength and dual-wavelength QML pulses are obtained by adjusting the PCs. Moreover, the central wavelength of the single-wavelength QML operation can be tuned from 1028.81 nm to 1039.20 nm, and the spacing of the dual-wavelength QML operation can be tuned from 0.93 nm to 5.79 nm. The obtained results indicate that QML pulses can be produced in the MMF laser, and such a flexible and functional laser would contribute to the application in fields of optical sensing, laser measuring, and processing.
References
[1] D. J. Richardson, J. M. Fini, L. E. Nelson. Space-division multiplexing in optical fibres. Nat. Photon., 7, 354(2013).
[2] H. R. Stuart. Dispersive multiplexing in multimode optical fiber. Science, 289, 281(2000).
[3] D. J. Richardson, J. Nilsson, W. A. Clarkson. High power fiber lasers: current status and future perspectives [Invited]. J. Opt. Soc. Am. B, 27, B63(2010).
[4] I. N. Papadopoulos, S. Farahi, C. Moser, D. Psaltis. High-resolution, lensless endoscope based on digital scanning through a multimode optical fiber. Biomed. Opt. Express, 4, 260(2013).
[5] M. Plöschner, T. Tyc, T. Čižmár. Seeing through chaos in multimode fibres. Nat. Photon., 9, 529(2015).
[6] I. Barmes, S. Witte, K. S. E. Eikema. Spatial and spectral coherent control with frequency combs. Nat. Photon., 7, 38(2013).
[7] H. Defienne, M. Barbieri, I. A. Walmsley, B. J. Smith, S. Gigan. Two-photon quantum walk in a multimode fiber. Sci. Adv., 2, e1501054(2016).
[8] B. Redding, H. Cao. Using a multimode fiber as a high-resolution, low-loss spectrometer. Opt. Lett., 37, 3384(2012).
[9] L. G. Wright, S. Wabnitz, D. N. Christodoulides, F. W. Wise. Ultrabroadband dispersive radiation by spatiotemporal oscillation of multimode waves. Phys. Rev. Lett., 115, 223902(2015).
[10] L. G. Wright, D. N. Christodoulides, F. W. Wise. Controllable spatiotemporal nonlinear effects in multimode fibres. Nat. Photon., 9, 306(2015).
[11] K. Krupa, A. Tonello, A. Barthélémy, V. Couderc, B. M. Shalaby, A. Bendahmane, G. Millot, S. Wabnitz. Observation of geometric parametric instability induced by the periodic spatial self-imaging of multimode waves. Phys. Rev. Lett., 116, 183901(2016).
[12] R. Dupiol, A. Bendahmane, K. Krupa, A. Tonello, M. Fabert, B. Kibler, T. Sylvestre, A. Barthelemy, V. Couderc, S. Wabnitz, G. Millot. Far-detuned cascaded intermodal four-wave mixing in a multimode fiber. Opt. Lett., 42, 1293(2017).
[13] U. Teğin, B. Ortaç. Spatiotemporal instability of femtosecond pulses in graded-index multimode fibers. IEEE Photon. Tech. Lett., 29, 2195(2017).
[14] G. Lopez-Galmiche, Z. Sanjabi Eznaveh, M. A. Eftekhar, J. Antonio Lopez, L. G. Wright, F. Wise, D. Christodoulides, R. A. Correa. Visible supercontinuum generation in a graded index multimode fiber pumped at 1064 nm. Opt. Lett., 41, 2553(2016).
[15] K. Krupa, C. Louot, V. Couderc, M. Fabert, R. Guenard, B. M. Shalaby, A. Tonello, D. Pagnoux, P. Leproux, A. Bendahmane, R. Dupiol, G. Millot, S. Wabnitz. Spatiotemporal characterization of supercontinuum extending from the visible to the mid-infrared in a multimode graded-index optical fiber. Opt. Lett., 41, 5785(2016).
[16] M. A. Eftekhar, L. G. Wright, M. S. Mills, M. Kolesik, R. A. Correa, F. W. Wise, D. N. Christodoulides. Versatile supercontinuum generation in parabolic multimode optical fibers. Opt. Express, 25, 9078(2017).
[17] K. Krupa, A. Tonello, V. Couderc, A. Barthélémy, G. Millot, D. Modotto, S. Wabnitz. Spatiotemporal light-beam compression from nonlinear mode coupling. Phys. Rev. A, 97, 043836(2018).
[18] K. Krupa, A. Tonello, B. M. Shalaby, M. Fabert, A. Barthélémy, G. Millot, S. Wabnitz, V. Couderc. Spatial beam self-cleaning in multimode fibres. Nat. Photon., 11, 237(2017).
[19] L. G. Wright, Z. Liu, D. A. Nolan, M.-J. Li, D. N. Christodoulides, F. W. Wise. Self-organized instability in graded-index multimode fibres. Nat. Photon., 10, 771(2016).
[20] Z. Liu, L. G. Wright, D. N. Christodoulides, F. W. Wise. Kerr self-cleaning of femtosecond-pulsed beams in graded-index multimode fiber. Opt. Lett., 41, 3675(2016).
[21] R. Guenard, K. Krupa, R. Dupiol, M. Fabert, A. Bendahmane, V. Kermene, A. Desfarges-Berthelemot, J. L. Auguste, A. Tonello, A. Barthélémy, G. Millot, S. Wabnitz, V. Couderc. Kerr self-cleaning of pulsed beam in an ytterbium doped multimode fiber. Opt. Express, 25, 4783(2017).
[22] E. Deliancourt, M. Fabert, A. Tonello, K. Krupa, A. Desfarges-Berthelemot, V. Kermene, G. Millot, A. Barthélémy, S. Wabnitz, V. Couderc. Kerr beam self-cleaning on the LP11 mode in graded-index multimode fibers. OSA Continuum, 2, 1089(2019).
[23] B. Morasse, S. Chatigny, C. Desrosiers, É. Gagnon, M.-A. Lapointe, J.-P. De. Simple design for singlemode high power CW fiber laser using multimode high NA fiber. Proc. SPIE, 7195, 719505(2009).
[24] L. Li, Q. Lou, J. Zhou, J. Dong, Y. Wei, J. Li. High power low-order modes operation of a multimode fiber laser. Chin. Opt. Lett., 5, 221(2007).
[25] L. G. Wright, D. N. Christodoulides, F. W. Wise. Spatiotemporal mode-locking in multimode fiber lasers. Science, 358, 94(2017).
[26] U. Teğin, B. Rahmani, E. Kakkava, D. Psaltis, C. Moser. All-fiber spatiotemporally mode-locked laser with multimode fiber-based filtering. Opt. Express, 28, 23433(2020).
[27] U. Teğin, B. Rahmani, E. Kakkava, D. Psaltis, C. Moser. Single-mode output by controlling the spatiotemporal nonlinearities in mode-locked femtosecond multimode fiber lasers. Adv. Photon., 2, 056005(2020).
[28] Y. Ding, X. Xiao, K. Liu, S. Fan, X. Zhang, C. Yang. Spatiotemporal mode-locking in lasers with large modal dispersion. Phys. Rev. Lett., 126, 093901(2021).
[29] Y. Ding, X. Xiao, P. Wang, C. Yang. Multiple-soliton in spatiotemporal mode-locked multimode fiber lasers. Opt. Express, 27, 11435(2019).
[30] H. Qin, X. Xiao, P. Wang, C. Yang. Observation of soliton molecules in a spatiotemporal mode-locked multimode fiber laser. Opt. Lett., 43, 1982(2018).
[31] U. Teğin, E. Kakkava, B. Rahmani, D. Psaltis, C. Moser. Spatiotemporal self-similar fiber laser. Optica, 6, 1412(2019).
[32] K. Liu, X. Xiao, X. Zhang, C. Yang. Multimode Q-switching and spatiotemporal mode-locking in multimode fiber lasers. Conference on Lasers and Electro-Optics, SM4P.2(2020).
[33] R. Miao, M. Tong, K. Yin, H. Ouyang, Z. Wang, X. Zheng, X. A. Cheng, T. Jiang. Soliton mode-locked fiber laser with high-quality MBE-grown Bi2Se3 film. Chin. Opt. Lett., 17, 071403(2019).
[34] H. Gu, Z. Qin, G. Xie, T. Hai, P. Yuan, J. Ma, L. Qian. Generation of 131 fs mode-locked pulses from 2.8 µm Er:ZBLAN fiber laser. Chin. Opt. Lett., 18, 031402(2020).
[35] P. Cheng, Y. Du, M. Han, X. Shu. Mode-locked and Q-switched mode-locked fiber laser based on a ferroferric-oxide nanoparticles saturable absorber. Opt. Express, 28, 13177(2020).
[36] U. Chakravarty, S. Gurram, A. Kuruvilla, B. N. Upadhyaya, K. S. Bindra. Short pulse generation in active Q-switched Yb-doped all fiber laser and its amplification. Opt. Laser Technol., 109, 186(2019).
[37] Z.-C. Luo, M. Liu, H. Liu, X.-W. Zheng, A.-P. Luo, C.-J. Zhao, H. Zhang, S.-C. Wen, W.-C. Xu. 2 GHz passively harmonic mode-locked fiber laser by a microfiber-based topological insulator saturable absorber. Opt. Lett., 38, 5212(2013).
[38] K. Kieu, M. Mansuripur. Tuning of fiber lasers by use of a single-mode biconic fiber taper. Opt. Lett., 31, 2435(2006).
[39] J.-G. Long, Y.-X. Gao, W. Lin, J.-W. Wu, X.-B. Lin, W.-Y. Hong, H. Cui, Z.-C. Luo, W.-C. Xu, A.-P. Luo. Switchable and spacing tunable dual-wavelength spatiotemporal mode-locked fiber laser. Opt. Lett., 46, 588(2021).
[40] T. Hakulinen, O. G. Okhotnikov. 8 ns fiber laser Q switched by the resonant saturable absorber mirror. Opt. Lett., 32, 2677(2007).
[41] J. J. Zayhowski, P. L. Kelley. Optimization of Q-switched lasers. IEEE J. Quantum Electron., 27, 2220(1991).
[42] C. S. Jun, S. Y. Choi, F. Rotermund, B. Y. Kim, D.-I. Yeom. Toward higher-order passive harmonic mode-locking of a soliton fiber laser. Opt. Lett., 37, 1862(2012).
[43] Y.-L. Qi, H. Liu, H. Cui, Y.-Q. Huang, Q.-Y. Ning, M. Liu, Z.-C. Luo, A.-P. Luo, W.-C. Xu. Graphene-deposited microfiber photonic device for ultrahigh-repetition rate pulse generation in a fiber laser. Opt. Express, 23, 17720(2015).
[44] J. C. Jing, X. Wei, L. V. Wang. Spatio-temporal-spectral imaging of non-repeatable dissipative soliton dynamics. Nat. Commun., 11, 2059(2020).
[45] Y. Guo, X. Wen, W. Lin, W. Wang, X. Wei, Z. Yang. Real-time multispeckle spectral-temporal measurement unveils the complexity of spatiotemporal solitons. Nat. Commun., 12, 67(2021).
Set citation alerts for the article
Please enter your email address