• Advanced Photonics
  • Vol. 3, Issue 2, 026001 (2021)
Xiao Tian Yan1、†, Wenxuan Tang1、2、*, Jun Feng Liu1, Meng Wang1, Xin Xin Gao1, and Tie Jun Cui1、2、*
Author Affiliations
  • 1Southeast University, School of Information Science and Engineering, State Key Laboratory of Millimeter Waves, Nanjing, China
  • 2Southeast University, Institute of Electromagnetic Space, Nanjing, China
  • show less
    DOI: 10.1117/1.AP.3.2.026001 Cite this Article Set citation alerts
    Xiao Tian Yan, Wenxuan Tang, Jun Feng Liu, Meng Wang, Xin Xin Gao, Tie Jun Cui. Glide symmetry for mode control and significant suppression of coupling in dual-strip SSPP transmission lines[J]. Advanced Photonics, 2021, 3(2): 026001 Copy Citation Text show less

    Abstract

    Glide symmetry, which is one kind of higher symmetry, is introduced in a special type of plasmonic metamaterial, the transmission lines (TLs) of spoof surface plasmon polaritons (SSPPs), in order to control the dispersion characteristics and modal fields of the SSPPs. We show that the glide-symmetric TL presents merged pass bands and mode degeneracy, which lead to broad working bandwidth and extremely low coupling between neighboring TLs. Dual-conductor SSPP TLs with and without glide symmetry are arranged in parallel as two channels with very deep subwavelength separation (e.g., λ0 / 100 at 5 GHz) for the application of integrated circuits and systems. Mutual coupling between the hybrid channels is analyzed using coupled mode theory and characterized in terms of scattering parameters and near-field distributions. We demonstrate theoretically and experimentally that the hybrid TL array obtains significantly more suppressed crosstalk than the uniform array of two nonglide symmetric TLs. Hence, it is concluded that the glide symmetry can be adopted to flexibly design the propagation of SSPPs and benefit the development of highly compact plasmonic circuits.

    1 Introduction

    Surface plasmon polaritons (SPPs) are highly localized surface waves that exist on the interface of metal and dielectric beyond the far-infrared frequency. However, they do not naturally exist at lower frequencies such as terahertz and microwaves, where the metals no longer behave like plasma with negative dielectric constants.1 In order to allow SPPs to operate in the lower frequency bands, spoof surface plasmon polaritons (SSPPs) have been conceived and realized on periodically structured metallic surfaces.2 Similar to the optical SPPs, SSPPs exhibit highly localized electromagnetic (EM) fields, subwavelength resolution, and extraordinary field confinements.3 Furthermore, ultrathin corrugated metallic strips have been proposed as kind of slow-wave waveguide that supports the propagation of SSPPs.4 Different types of SSPP transmission lines (TLs), including single-conductor and dual-conductor ones, have been created in different circumstances. Because of mode and momentum mismatch, transitions from the conventional TLs such as coplanar waveguide and microstrip (MS) are needed to realize high-efficiency excitation of SSPPs.57 In addition, a series of devices, such as filters, resonators, amplifiers, demultiplexers, and antennas, has been demonstrated,813 and an integrated wireless communication system based on SSPPs has been recently developed.14 The SSPP circuits are highly expected to offer new solutions for future integrated and smart systems due to the designable dispersion characteristics, high efficiency, low bending loss, low crosstalk, conformal transmissions, and low interference with EM waves in the environment.1518

    On the other hand, the SSPP structures can be considered as special kinds of metamaterials that are composed of periodically arranged subwavelength unit cells. It has been demonstrated that higher symmetries can effectively affect the dispersion characteristics and band gaps of structures.19 Higher symmetry occurs if the periodic structure can be described by additional geometric operations beyond a simple translation or reflection. For example, glide and twist symmetries are two common cases of higher symmetry.20,21 Most recently, metamaterials with glide symmetry have been developed to achieve flexible control of dispersion behaviors and band gaps, so as to provide new solutions for microwave waveguides, functional devices, and antennas.2224

    Here, we introduce glide symmetry in dual-conductor SSPP TLs and TL arrays for characteristics control. First, the dispersion curves, modal fields, and transmission properties of the glide symmetric TL are studied, and degeneracy of the fundamental mode is investigated. After that, two SSPP TLs, one with glide symmetry and one without glide symmetry, are arranged in parallel as two channels with deep subwavelength separation (which is λ0/100 at 5 GHz). Mutual coupling between the hybrid channels is analyzed based on coupled mode theory and characterized in terms of scattering parameters and near-field distributions. Simulated and measured results are presented, showing that the hybrid TL array obtains much higher channel isolation and lower crosstalk than the uniform array composed of two nonglide symmetric TLs. Finally, conclusions are drawn and potential applications are discussed.

    2 Glide Symmetry in Dual-Strip SSPP TLs

    The SSPP TLs typically consist of metallic strips with subwavelength corrugations and sometimes with ground. Their configurations (e.g., the geometry of the strips) can be adjusted according to specific requirements in applications. There have been several types of SSPP TLs reported in the literature, which could be generally categorized as single-strip, grounded single-strip, and dual-strip.4,7,8 Among them, the dual-strip SSPP TLs contain two layers of antisymmetrically arranged corrugated metallic strips on both sides of dielectric substrate. Compared to the single-strip SSPP TLs of the same size, the dual-strip ones obtain lower cutoff frequency, stronger subwavelength effect and field confinement, further depressed mutual coupling, and easier embedment of lumped elements and active devices.25 In view of these, we introduce glide symmetry in the dual-strip SSPP TLs to further improve the performance of plasmonic circuits.

    A unit cell of the dual-strip SSPP TL, which has two antisymmetrically arranged metallic structures, is given in Fig. 1(a). For comparison, the unit cell with glide symmetry is given in Fig. 1(b). The misalignment between the upper and lower strips is indicated by the glide distance between the centers of the upper and lower slots (which is denoted as gl in the figure). When there is no glide symmetry introduced in the structure, the upper and lower metallic strips are aligned along the x axis with gl=0. When the glide symmetry is introduced, the misalignment is no longer zero.

    (a) A nonglide unit cell in the dual-strip SSPP TL. The line width, period, width, and depth of the slots are h=6 mm, p=3.6 mm, a=0.8 mm, and d=5.2 mm, respectively. In this work, the thickness of the two metal layers is t=0.018 mm, and the substrate has a relative permittivity of 3.48 with thickness of tsub=0.762 mm and width of wsub=30 mm. (b) A glide symmetric unit cell. The centers of the slots in the upper and lower layers are misaligned with a glide distance of gl=0.5p along the x axis. (c) The glide symmetric dual-strip SSPP TL. Section I is the MS line at the input and output, and the widths of the upper and lower strips are w0=1.7 mm and wgnd=25 mm, respectively. Section II is the transition section and Section III is composed of uniform glide symmetric unit cells.

    Figure 1.(a) A nonglide unit cell in the dual-strip SSPP TL. The line width, period, width, and depth of the slots are h=6  mm, p=3.6  mm, a=0.8  mm, and d=5.2  mm, respectively. In this work, the thickness of the two metal layers is t=0.018  mm, and the substrate has a relative permittivity of 3.48 with thickness of tsub=0.762  mm and width of wsub=30  mm. (b) A glide symmetric unit cell. The centers of the slots in the upper and lower layers are misaligned with a glide distance of gl=0.5p along the x axis. (c) The glide symmetric dual-strip SSPP TL. Section I is the MS line at the input and output, and the widths of the upper and lower strips are w0=1.7  mm and wgnd=25  mm, respectively. Section II is the transition section and Section III is composed of uniform glide symmetric unit cells.

    To compare the EM properties of the nonglide and glide symmetric structures, dispersion characteristics are studied in the commercial software of CST Microwave Studio. The dashed lines in Fig. 2 are the dispersion curves of the first four modes of the nonglide symmetric SSPP structure. The cutoff frequency of the fundamental mode (mode 1 in Fig. 2) is about 5 GHz, indicating that the SSPP wave in this mode can propagate below 5 GHz but becomes evanescent above this frequency. At higher frequencies, higher-mode SSPPs may also propagate according to the higher-mode dispersion curves, and stop bands are observed between neighboring propagating modes, indicating the standing waves at the Brillouin zone boundary. For the glide symmetric SSPP structure, we have tested different misalignments and find that when the misalignment is half periodicity (gl=0.5  p) there exists a degeneracy with nonzero group velocity of the supported modes at the Brillouin zone boundary. In particular, the first and second modes, as well as the third and fourth modes, coalesce at the edge of the first zone of the Brillouin diagram, and their dispersion curves are considered as part of the same mode, as illustrated by the four solid lines in Fig. 2. The band gap between the first and second modes, and the one between the third and fourth modes, disappear in the glide symmetric structure. As a result, the cutoff frequency of the fundamental mode (the first mode) increases from 5 to 9.5 GHz, indicating that the glide symmetric SSPP TL obtains a significantly broadened working band without extra space or cost.

    Dispersion diagram of the nonglide and glide symmetric unit cells.

    Figure 2.Dispersion diagram of the nonglide and glide symmetric unit cells.

    The degeneracy of the fundamental mode is also studied in terms of the distribution of EM fields. We choose two cross sections in the unit cell, as indicated by the orange plane and the blue one in Figs. 1(a) and 1(b), to observe the near-electric fields in the nonglide and glide symmetric SSPP structures. For the nonglide symmetric one, the electric field of the fundamental mode is nearly asymmetrically distributed in both cross sections [see Figs. 3(a) and 3(b)], which is naturally decided by the antiarrangement of the upper and lower strips. In other words, the fundamental mode of the nonglide SSPP TL is approximately an odd mode with the cutoff frequency of 5.2 GHz. Between the fundamental mode and the first higher mode (the second mode), there exists a band gap where no SSPP wave can propagate. In contrast, for the glide symmetry, there are both even and odd components included in the total field,26 and the distributions of the field become more uniform in different cross sections [e.g., the field distribution in Fig. 3(c) is similar to that in Fig. 3(d) when flipped], which is mainly due to the glide symmetric property of the structure. Meanwhile, the cutoff frequency of the fundamental mode changes to 9.5 GHz since the first band gap is eliminated. The change of modal field and band gap is due to the degeneracy of modes when higher symmetry is introduced in the structure. We remark that the fundamental modes of the nonglide and glide symmetric SSPP TLs have essentially high isolation because of the enhanced orthogonality of EM fields. This important characteristic could be utilized in the design of compact TL arrays, as is discussed in Sec. 3.

    (Side view) (a), (b) Distributions of the electric fields of the nonglide symmetric structure at the orange and the blue cross sections indicated in Fig. 1(a), respectively. (c), (d) Distributions of the electric fields of the glide symmetric structure at the orange and the blue cross sections indicated in Fig. 1(b), respectively.

    Figure 3.(Side view) (a), (b) Distributions of the electric fields of the nonglide symmetric structure at the orange and the blue cross sections indicated in Fig. 1(a), respectively. (c), (d) Distributions of the electric fields of the glide symmetric structure at the orange and the blue cross sections indicated in Fig. 1(b), respectively.

    The entire model of the glide symmetric SSPP TL is shown in Fig. 1(c). Similar to the dual-strip SSPP TL reported in Ref. 17, the glide symmetric one includes three sections: Section I contains MS lines at the input and output, Section II contains transitions between the MS lines and SSPP structures, and Section III contains uniform unit cells that support the propagation of SSPPs. In the transitions, the quasitransverse electromagnetic mode on the MS line is transformed to the TM mode of SSPPs, and vice versa. In order to realize smooth matching of impedance and momentum, the widths of the upper and lower strips (w0 and wgnd, respectively) and the depth of slot (d) are changed gradually. The prototypes of nonglide and glide symmetric TLs were fabricated on a Rogers RO4350B substrate with relative permittivity of 3.48 and thickness of 0.762 mm. The transmission coefficients (S21) and reflection coefficients (S11) of both TLs were measured using an Agilent vector network analyzer (VNA) and plotted in Fig. 4. In terms of the transmission coefficient, the nonglide symmetric TL has a cutoff frequency of about 5.4 GHz while the glide symmetric one has a cutoff frequency of about 9.6 GHz, which agrees quite well with the dispersion curves plotted in Fig. 2. Therefore, it is proved that the bandwidth could be significantly increased (almost double) for the glide symmetric SSPP TL, while the size of it remains the same as that of the nonglide one. According to the dispersion curve of the glide symmetric SSPP TL, we remark that the higher-frequency part of the fundamental mode (approximately from 5.4 to 9.6 GHz) is a hybrid mode including both forward harmonic (with a positive wave velocity) and backward harmonic (with a negative wave velocity). Further investigations may be carried out in the future so as to excite a purer backward harmonic for novel properties and functionalities.

    Measured reflection coefficients (S11) and transmission coefficients (S21).

    Figure 4.Measured reflection coefficients (S11) and transmission coefficients (S21).

    The distributions of the near electric fields are measured in our home-made near-field scanning system, which is mainly constructed by a two-dimensional (2D) stepper and the VNA. The magnitudes of the electric fields right above the nonglide and glide symmetric TLs are measured and plotted in Fig. 5. For the nonglide TL, the SSPP wave propagates below the cutoff frequency of 5.4 GHz (e.g., at 5.3 GHz) but becomes evanescent beyond it (e.g., at 5.9 GHz). In contrast, for the glide symmetric TL, the SSPP wave can propagate below the cutoff frequency of 9.6 GHz (e.g., at 5.3, 5.9, and 8.5 GHz) with gradually decreased transmission efficiency.

    Magnitude distributions of the near electric field for (a) the nonglide symmetric and (b) the glide symmetric SSPP TLs at different frequencies.

    Figure 5.Magnitude distributions of the near electric field for (a) the nonglide symmetric and (b) the glide symmetric SSPP TLs at different frequencies.

    3 Hybrid Nonglide and Glide Symmetric TL Array

    Channel crosstalk is inevitable in compact systems, due to mutual coupling between TLs and components. When TLs are densely arranged, e.g., with subwavelength separation, the EM fields on one TL will give rise to induced currents on other TLs and therefore cause unwanted coupling. In fact, channel crosstalk suppression and signal integrity are two key problems in modern integrated circuits, and, unfortunately, they are almost contradictory. The SSPP TLs have natural advantages in view of coupling suppression, due to the strong subwavelength effect and field confinement. Here, we propose a hybrid array composed of alternatively arranged nonglide and glide symmetric TLs, which possesses extremely low mutual couplings.

    A simplified two-channel model is used to investigate the isolation and coupling characteristics of the hybrid TL array, as is given in Fig. 6. This is a four-port network composed of two channels; one is the nonglide symmetric TL channel, and the other is the glide symmetric one. Each TL includes three sections, as discussed in Fig. 1(c). The size of the unit cell, dielectric substrate, and metal thickness are the same for both TLs. The four ports are named clockwise, as shown in Fig. 6. Separation between the two TLs is indicated by dis in the straight section (Section III), which is in the deep subwavelength scale.

    The four-port model composed of two channels; one is the nonglide symmetric TL channel, and the other is the glide symmetric one.

    Figure 6.The four-port model composed of two channels; one is the nonglide symmetric TL channel, and the other is the glide symmetric one.

    κab=ωε04s(n2ne2)[Eat*·Ebt+(ne2n2)Eax*·Ebx]dS.

    Simulated isolation coefficients (S41 and S14) and coupling coefficients (S31 and S24) of the two SSPP TLs.

    Figure 7.Simulated isolation coefficients (S41 and S14) and coupling coefficients (S31 and S24) of the two SSPP TLs.

    Here, ne is the equivalent refractive index of TLs in the array.

    Next, we use Eq. (2) to compare the coupling coefficient between two identical nonglide symmetric SSPP TLs and that between a nonglide TL and a glide one. Eat and Ebt are the transverse electric fields of the fundamental modes in the nonglide and glide symmetric SSPP TLs, respectively, which are calculated in CST using eigenmode simulation; Eax and Ebx are the longitudinal ones. The normalized and average values of the mode coupling coefficient are given in Fig. 8. When the separation is 0.6 mm, which is λ0/100 at 5 GHz, we observe that the coupling coefficient between the glide symmetric and the nonglide symmetric TLs (see the solid black line) is significantly lower than that between two nonglide symmetric TLs (see the dashed black line) from 0 to 5 GHz. In particular, as the working frequency approaches the cutoff frequency of 5.4 GHz, field localization increases around the SSPP TLs in the subwavelength scale, and thus the dashed black line rises quickly at high frequencies. In contrast, the solid black line is almost flat, indicating that the channel isolation is effectively improved when a nonglide TL is replaced by a glide symmetric one. When the separation is 2 mm, the two mode coupling coefficients (see the solid red line and the dashed red line) become lower and comparable, indicating that the dual-strip SSPP TL array, whether hybrid or uniform, possesses remarkable channel isolation at subwavelength separation due to the significant field confinement of SSPPs.

    The normalized and average mode coupling coefficients in two types of TL arrays at different line separations (dis=0.6 mm and dis=2 mm).

    Figure 8.The normalized and average mode coupling coefficients in two types of TL arrays at different line separations (dis=0.6  mm and dis=2  mm).

    A prototype of the hybrid array containing nonglide and glide symmetric TLs (as given in Fig. 6) and a control prototype of two uniform nonglide symmetric TLs are fabricated and measured for demonstration. The reflection coefficient S11, transmission coefficient S21, coupling coefficient S31, and isolation coefficient S41 are measured and plotted in Fig. 9. The four-port networks are fed through the nonglide symmetric TLs at port 1 (see Fig. 6 for reference), and two separations (0.6 and 2 mm) are involved in comparisons. In Figs. 9(a) and 9(b), the S11 curves are observed to be similar for the hybrid TL array and the uniform TL array with both separations. When the line separation is 0.6 mm, the S21 curve of the hybrid TL array is higher than that of the uniform TL array from 3.4 to 5.3 GHz in both simulation and measurement results, showing higher transmission in the hybrid TL array, as given in Fig. 9(c). When the line separation is 2 mm, however, both TL arrays have similar transmission performance, as shown in Fig. 9(d). Significantly different coupling coefficients (S31) are shown in Figs. 9(e) and 9(f), showing that much less energy could be coupled to the neighboring TL in the hybrid array when compared with the uniform nonglide array. In view of this, the employment of glide symmetry helps to suppress the channel crosstalk without bringing extra space and feeding networks. Better isolation in the hybrid TL array is also shown in Figs. 9(g) and 9(h) in term of the S41 curves. We remark that the crosstalk suppression is mainly due to the hybrid configuration of the TL array that increases the channel isolation. If two glide symmetric TLs, instead of two nonglide ones, are adopted to compose the uniform array, the crosstalk in the TL array is much higher than that of the hybrid one in terms of S31 and S41. In Fig. 9, the simulated S parameters of the uniform glide symmetric TL array are also plotted, showing comparable transmission, reflection, coupling, and isolation coefficients with those of the uniform nonglide symmetric TL array.

    Comparison of the reflection coefficient (S11), transmission coefficient (S21), coupling coefficient (S31), and isolation coefficient (S41) for the hybrid TL array (composed of a glide symmetric TL and a nonglide symmetric TL) and the uniform TL arrays (composed of two nonglide symmetric TLs and two glide symmetric TLs, respectively).

    Figure 9.Comparison of the reflection coefficient (S11), transmission coefficient (S21), coupling coefficient (S31), and isolation coefficient (S41) for the hybrid TL array (composed of a glide symmetric TL and a nonglide symmetric TL) and the uniform TL arrays (composed of two nonglide symmetric TLs and two glide symmetric TLs, respectively).

    The coupling suppression in the hybrid TL array is also investigated in terms of the distributions of near-electric fields, and low-coupling and high-isolation are observed at different frequencies (2 and 5 GHz) and with different separations (0.6 and 2 mm) in both simulation and experiment results, as presented in Fig. 10. Clearly, due to mode mismatch in the hybrid array, very limited portion of energy could be coupled to the neighboring TL and then received at the isolated and coupled ports. This characteristic provides us with a new TL array scheme with low channel crosstalk, improved signal accuracy, and no extra space.

    Distributions of the near-electric field of the hybrid TL array and the uniform TL array with line separations being 0.6 and 2 mm at 2 and 5 GHz, respectively.

    Figure 10.Distributions of the near-electric field of the hybrid TL array and the uniform TL array with line separations being 0.6 and 2 mm at 2 and 5 GHz, respectively.

    4 Experimental Setup and Methods

    4.1 S-Parameter Measurement

    A VNA (Agilent N5230C) was used to perform spectrum measurements of the two-port networks with one SSPP TL and the four-port networks with two SSPP TLs, including all the scattering parameters.

    4.2 Near-Field Measurement

    Near electric field distributions in the SSPP TLs were measured in our home-made 2D near-field scanning system in the microwave anechoic chamber at Southeast University. The 2D near-field scanning system includes a VNA (Agilent N5230C) and three electronic motor steppers in the X-, Y-, and Z-directions, respectively. The experimental sample was placed on a platform supported by the X- and Y-steppers, and a monopole was placed 2 mm above the sample so as to measure the vertical (z) component of the electric fields continuously when the platform moves in the XoY plane. The test region of the near fields was 230  mm×60  mm (for TL arrays) and 130  mm×40  mm (for TLs), and the moving step of the electronic motor was 1 mm.

    5 Conclusion

    In this work, we introduce glide symmetry, which is a typical type of higher symmetry, to manipulate the dispersion characteristics of the SSPP structure. Mode degeneracy and merged pass-bands are investigated and designed so as to broaden the bandwidth and control the propagation modes of SSPPs. We further propose a hybrid SSPP TL array composed of alternately arranged nonglide and glide symmetric SSPP TLs. Although the two neighboring TLs possess the same composing units, strip width, and feeding structure, mutual coupling has been significantly suppressed due to the mode mismatch introduced by the glide symmetry in the structure. Both simulations and experiments have been carried out for demonstration. This glide symmetric SSPP TL, as well as the hybrid array, can be adopted in highly compact circuits without bringing in extra space and feeding networks. In view of this, we conclude that glide symmetry offers supplementary control of the SSPP waves, which may bring about new solutions in future integrated plasmonic circuits.

    References

    [1] W. L. Barnes, A. Dereux, T. W. Ebbesen. Surface plasmon subwavelength optics. Nature, 424, 824-830(2003).

    [2] J. B. Pendry. Mimicking surface plasmons with structured surfaces. Science, 305, 847-848(2004).

    [3] W. X. Tang et al. Concept, theory, design, and applications of spoof surface plasmon polaritons at microwave frequencies. Adv. Opt. Mater., 7, 1800421(2019).

    [4] X. Shen et al. Conformal surface plasmons propagating on ultrathin and flexible films. Proc. Natl. Acad. Sci. U. S. A., 110, 40-45(2013).

    [5] H. F. Ma et al. Broadband and high-efficiency conversion from guided waves to spoof surface plasmon polaritons: broadband and high-efficiency conversion from guided waves to spoof surface plasmon polaritons. Laser Photonics Rev., 8, 146-151(2014).

    [6] L. Liu et al. Multi-channel composite spoof surface plasmon polaritons propagating along periodically corrugated metallic thin films. J. Appl. Phys., 116, 013501(2014).

    [7] W. Zhang et al. Trapping of surface plasmon wave through gradient corrugated strip with underlayer ground and manipulating its propagation. Appl. Phys. Lett., 106, 021104(2015).

    [8] H. C. Zhang et al. Broadband amplification of spoof surface plasmon polaritons at microwave frequencies: amplification of spoof surface plasmon polaritons. Laser Photonics Rev., 9, 83-90(2015).

    [9] Q. Zhang et al. A hybrid circuit for spoof surface plasmons and spatial waveguide modes to reach controllable band-pass filters. Sci. Rep., 5, 16531(2015).

    [10] X. Shen, T. J. Cui. Planar plasmonic metamaterial on a thin film with nearly zero thickness. Appl. Phys. Lett., 102, 211909(2013).

    [11] Y. J. Zhou, B. J. Yang. A 4-way wavelength demultiplexer based on the plasmonic broadband slow wave system. Opt. Express, 22, 21589-21599(2014).

    [12] J. Y. Yin et al. Endfire radiations of spoof surface plasmon polaritons. Antennas Wireless Propag. Lett., 16, 597-600(2017).

    [13] Q. Zhang, Q. Zhang, Y. Chen. Spoof surface plasmon polariton leaky-wave antennas using periodically loaded patches above PEC and AMC ground planes. Antennas Wireless Propag. Lett., 16, 3014-3017(2017).

    [14] H. C. Zhang et al. A plasmonic route for the integrated wireless communication of subdiffraction-limited signals. Light Sci. Appl., 9, 113(2020).

    [15] W. X. Tang et al. Reduction of radiation loss at small-radius bend using spoof surface plasmon polariton transmission line. Sci. Rep., 7, 41077(2017).

    [16] A. Kianinejad, Z. N. Chen, C.-W. Qiu. Low-loss spoof surface plasmon slow-wave transmission lines with compact transition and high isolation. IEEE Trans. Microwave Theory Tech., 64, 3078-3086(2016).

    [17] H. C. Zhang et al. Breaking the challenge of signal integrity using time-domain spoof surface plasmon polaritons. ACS Photonics, 2, 1333-1340(2015).

    [18] Y. Liang et al. On-chip sub-terahertz surface plasmon polariton transmission lines in CMOS. Sci. Rep., 5, 14853(2015).

    [19] A. Hessel et al. Propagation in periodically loaded waveguides with higher symmetries. Proc. IEEE, 61, 183-195(1973).

    [20] P. Padilla et al. Glide symmetry to prevent the lowest stopband of printed corrugated transmission lines. IEEE Microwave Wireless Comp. Lett., 28, 750-752(2018).

    [21] F. Ghasemifard, M. Norgren, O. Quevedo-Teruel. Twist and polar glide symmetries: an additional degree of freedom to control the propagation characteristics of periodic structures. Sci. Rep., 8, 11266(2018).

    [22] O. Quevedo-Teruel, M. Ebrahimpouri, M. Ng Mou Kehn. Ultrawideband metasurface lenses based on off-shifted opposite layers. Antennas Wireless Propag. Lett., 15, 484-487(2016).

    [23] L. Liu et al. Backward phase matching for second harmonic generation in negative-index conformal surface plasmonic metamaterials. Adv. Sci., 5, 1800661(2018).

    [24] L. Wang, J. L. Gomez-Tornero, O. Quevedo-Teruel. Substrate integrated waveguide leaky-wave antenna with wide bandwidth via prism coupling. IEEE Trans. Microwave Theory Tech., 66, 3110-3118(2018).

    [25] H. C. Zhang et al. Second-harmonic generation of spoof surface plasmon polaritons using nonlinear plasmonic metamaterials. ACS Photonics, 3, 139-146(2016).

    [26] G. Valerio et al. Glide-symmetric all-metal holey metasurfaces for low-dispersive artificial materials: modeling and properties. IEEE Trans. Microwave Theory Tech., 66, 3210-3223(2018).

    [27] A. Ma, Y. Li, X. Zhang. Coupled mode theory for surface plasmon polariton waveguides. Plasmonics, 8, 769-777(2013).

    Xiao Tian Yan, Wenxuan Tang, Jun Feng Liu, Meng Wang, Xin Xin Gao, Tie Jun Cui. Glide symmetry for mode control and significant suppression of coupling in dual-strip SSPP transmission lines[J]. Advanced Photonics, 2021, 3(2): 026001
    Download Citation